The Project Gutenberg eBook of Home labor saving devices
This ebook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this ebook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.
Title: Home labor saving devices
Author: Rhea C. Scott
Illustrator: R. E. Gamble
Release date: May 18, 2024 [eBook #73645]
Language: English
Original publication: Philadelphia: J. B. Lippincott Company, 1917
Credits: Carol Brown, Chris Curnow and the Online Distributed Proofreading Team at https://www.pgdp.net (This file was produced from images generously made available by The Internet Archive)
*** START OF THE PROJECT GUTENBERG EBOOK HOME LABOR SAVING DEVICES ***
[Illustration: CONVENIENT ARRANGEMENT FOR KITCHEN DEVICES]
HOME LABOR SAVING
DEVICES
BY
RHEA C. SCOTT
INSTRUCTOR IN HOME DEMONSTRATION WORK AT GEORGE PEABODY COLLEGE
FOR TEACHERS. NASHVILLE, TENN.;
FORMERLY ASSISTANT STATE DEMONSTRATION AGENT IN LOUISIANA.
ILLUSTRATED BY
MRS. R. E. GAMBLE
SECOND EDITION, REVISED.
[Illustration]
PHILADELPHIA AND LONDON
J. B. LIPPINCOTT COMPANY
COPYRIGHT, 1917, BY J. B. LIPPINCOTT COMPANY
COPYRIGHT, 1918, BY J. B. LIPPINCOTT COMPANY
_Electrotyped and Printed by J. B. Lippincott Company
At the Washington Square Press, Philadelphia, U. S. A._
TO THE WOMEN AND GIRLS OF THE FARM, LOVERS OF THE
FIELDS, AND FRIENDS OF THE FLOWERS, WHOSE HEARTS
HEAR THE CALL AND WHOSE HANDS SEEK THE SKILL TO
MAKE THE RURAL HOME A PLACE OF LIGHT, OF HEALTH,
OF BEAUTY, THIS LITTLE VOLUME IS AFFECTIONATELY
DEDICATED
PREFACE
The point of view from which this manual was written is indicated in
the introduction.
The aims are to increase efficiency in the farm home and to satisfy the
growing demand for useful information in the country schools.
This is done by giving suggestions and directions for practical work to
be done in the home and at school.
Throughout the country to-day many rural schools are expressing a
desire to add to their present school curricula courses which are
practical. The ideal kept in mind during the preparation of this manual
has been to supply that need and at the same time to make it possible
for any woman to use the book in her own home.
The limitations in the size have caused many omissions. It is the
intention of the author to enlarge upon this material as the demand
increases. Ideas and suggestions from other States have been dominant
throughout, thus carrying out the true demonstration point of view.
THE AUTHOR.
January, 1917.
ACKNOWLEDGMENTS
Acknowledgment and thanks are gratefully given to the following persons
for suggestions, use of material, and corrections:
Miss Ola Powell, United States Department of Agriculture, Washington,
D. C., for making this little volume possible by inspirational
suggestions furnished throughout the preparation of the manual and
especially for the use of her two models of jelly strainers and
illustrations on cheese making.
Mr. O. B. Martin, United States Department of Agriculture, Washington,
D. C., for his most valuable suggestions and sympathetic interest
during the entire preparation of the material.
The United States Department of Agriculture, Washington, D. C., for
photographs of roller tray wagon, water works system, and ideas
obtained from circular letter prepared by Miss Mary E. Creswell and
Miss Ola Powell, of the States Relations Service, Office of Extension
Work in the South.
Mr. Harry M. Lamon, Poultry Division of the Bureau of Animal Industry,
United States Department of Agriculture, Washington, D. C., for
illustrations of poultry house, dry mash hopper and chicken coop, and
the use of information in Farmers’ Bulletin, No. 574.
Mr. B. H. Rawl, Chief of the Dairy Division, Bureau of Animal Industry;
United States Department of Agriculture, Washington, D. C., and Mr. J.
H. McClain and other specialists in the Dairy Division for assistance
in taking the pictures and for criticisms and corrections of the
material.
Mr. N. E. D. Talcott, State Agent in Poultry Club Work in Virginia, for
the use of his dry mash hopper and oat-sprouting rack.
Dr. John W. Wayland, State Normal School, Harrisonburg, Va., for his
appropriate dedication.
Miss Elizabeth C. Cleveland, Head of the English Department, State
Normal School, Harrisonburg, Va., for reading and correcting manuscript.
Mrs. K. C. Blythe, Leesburg, Va., for permission to use a dish drainer.
Mr. C. E. Hanson, A. & M. College, College Station, Texas, for his
interest and helpful suggestions.
Miss Emma Chandler, State Agent in Home Demonstration Work, Stillwater,
Okla., for the use of iceless refrigerator No. 2 and directions for
making same.
Mr. Thos. H. Fullan, Alabama Polytechnic Institute, Auburn, Ala., for
the use of his milking stool and suggestions for making the shower bath.
Mrs. Helen Brown Wolcott, State Agent in Home Demonstration Work,
Lexington, Ky., for ideas for making the dish rack.
To “The Country Gentleman” for illustrations of cheese making.
Also others who have contributed to this volume.
CONTENTS
PAGE
INTRODUCTION 13-14
CHAPTER I
KITCHEN CONVENIENCES 15
Vegetable Paring Table, Wall Cabinet for the Kitchen,
Ironing Board, Jelly Strainer, No. 1 and No. 2, Dish
Drainer, Dish Rack, Coal Box, Wood Box, Fireless
Cooker, Home-made Cook Stove Drier.
CHAPTER II
DINING ROOM CONVENIENCES 43
Roller Tray Wagon, Sideboard, Screen.
CHAPTER III
PORCH EQUIPMENT 51
Iceless Refrigerator, No. 1 and No. 2, Umbrella Stand,
Blacking Box, Towel Roller, Porch Swing.
CHAPTER IV
MISCELLANEOUS EQUIPMENT 67
Dustless Mop, Folding Canning Table, Fly Trap,
Garbage Barrel, Scrubbing Chariot, Sewing Screen,
Shower Bath, Practical Waterworks System.
CHAPTER V
POULTRY DEVICES 84
Poultry House, Nests, Egg Tester, Dry Mash Hopper,
No. 1 and No. 2, Rack for Oat-Sprouting Trays, Dust
Boxes, Drinking Vessel, Chicken Brooder.
CHAPTER VI
DAIRY DEVICES 99
Butter-making, Butter Worker, Milking Stool,
Cheese-making Equipment.
APPENDIX
Fundamentals in Woodworking, Suggested List of Tools,
List of Publications for Supplementary Reading.
INDEX 117
ILLUSTRATIONS
PAGE
CONVENIENT ARRANGEMENT FOR KITCHEN DEVICES _Frontispiece_
AN EXHIBIT OF HOME-MADE LABOR SAVING DEVICES 14
HOME-MADE DRIERS READY FOR USE 36
ASSEMBLED MATERIAL FOR BUILDING A FIRELESS COOKER 40
ROLLER TRAY WAGON, INCLUDING COMPARTMENT FOR CHINA AND
A DRAWER FOR SILVER AND LINEN 44
ICELESS REFRIGERATOR 54
SEWING SCREEN 78
A PORTABLE POULTRY HOUSE, SHOWING THE EXTERIOR AND INTERIOR 84
CHURNING OPERATIONS 104
DRAWING THE CURD 108
PRESSING THE CURD 108
MOULDING THE CHEESE 109
NECESSARY EQUIPMENT USED IN CHEESE-MAKING 109
INTRODUCTION
BY PRESIDENT JULIAN A. BURRUSS
State Normal School for Women, Harrisonburg, Va.
No phase of modern social development has received more attention in
recent years than that of our rural population. Advances have been
striking along all lines of country life. It would, however, be too
much to say that the interests of women and their work in the home have
received the attention properly due them. Frequently farmers of the
highest type will equip their farms with the latest and best implements
and machinery for their work and yet will fail to provide their homes
with equipment equally as essential and desirable for the work of the
women members of their households. Women’s organizations and the agents
of the Home Demonstration Work, together with other agencies, have done
much to direct attention along this very important line and in many
communities labor-saving devices of a most ingenious character have
been developed.
What is good for one busy housewife is not too good for another, and it
is a good rule to push a good thing along for the benefit of others.
With this in view the author has gathered together numerous inventions
of home-made devices of a labor-saving and efficiency-increasing
kind, and describes them in this little volume so that all to whom
it may come may have the opportunity to make such contrivances, or
modifications of them, for their own use. In doing this, the author has
not merely had in her mind her own State, but has sought to recognize
the viewpoints of women in as many other States as possible.
The author is peculiarly fitted for the task she has set herself. As
Assistant State Agent for Home Demonstration Work in Virginia, under
the direction of the United States Department of Agriculture, and
as supervisor and community worker for a number of years in various
rural districts before assuming the duties of her present position,
she has had abundant facilities for becoming familiar with the
conditions prevailing in country homes. Having maintained sympathetic
relationships with country women for many years, she knows their
problems and their needs, and she is also familiar with the sources
from which help may be drawn.
There can be no real improvement in social life in the country unless
there is leisure time to be devoted to uplifting, cultural, and
recreational purposes. The only way in which this may be obtained is
by means of labor-saving and time-saving appliances. The articles here
described are intensely practical and may be readily made in any home
at a nominal cost. To make two blades of grass grow where one formerly
grew is certainly a very valuable achievement; but to save muscles and
nerves, and to give time and energy for mental and social and spiritual
development, is far more valuable and desirable. If the information
given in this book serves to lighten the burden and shorten the daily
drudgery of a single housewife, its publication will be justified; and
it should find a cordial reception in a multitude of homes.
[Illustration: AN EXHIBIT OF HOME-MADE LABOR SAVING DEVICES BY THE
CANNING CLUB AT THE STATE NORMAL SCHOOL, HARRISONBURG, VA.]
HOME LABOR SAVING
DEVICES
CHAPTER I
=KITCHEN CONVENIENCES=
VEGETABLE PARING TABLE
A convenient kitchen table made of poplar and covered with zinc with
an opening in the center through which the parings of vegetables or
the scraping of dishes may be put into a pail sitting on the lower
shelf. This saves soiling the floor and many steps while preparing
the vegetables for cooking. It should be remembered that the pail
underneath must be removed and the contents emptied into the garbage
barrel after each using. It is not a garbage pail and should in no
sense be used as such. Above the table hooks on which hang many smaller
cooking utensils, such as paring knives, graters, spoons, scissors, or
can openers, are all arranged to accommodate the housekeeper.
MATERIALS:
12’ poplar.
¼ lb. 6-penny nails to construct table.
1 piece of sheet zinc, 12” × 30”, to cover the top of table.
DIMENSIONS:
_Top_: 1 piece 1” thick × 18” wide × 26” long.
_Shelf_: 1 piece 1” thick × 10” wide × 32” long.
_Legs_: 4 pieces 1½” thick × 1½” wide × 24” long.
_Cleats_: 4 pieces 1” thick × 1” wide × 14” long.
DIRECTIONS:
After cutting legs, nail on cleats even with the top edge,
measuring 14” for the bottom cleat. Measure 2” from the ends
and sides of the top and nail on the legs. Measure 7¾” from
the right-hand end and 9” from the side and make a hole 8” in
diameter. Nail the bottom shelf at an equal distance from the
bottom of the legs.
[Illustration]
WALL CABINET FOR THE KITCHEN
(MADE FROM DRY GOODS BOXES)
A comfort to the housewife is a kitchen cabinet, containing different
compartments for spices and such accessories necessary in cooking. It
is made of boxes and should be put at some place convenient to the
work table so the woman will not have to move to get these things
when preparing a meal. It surely fulfils the old adage, “A place for
everything and everything in its place.”
MATERIALS:
1 box of the required dimensions to build the body.
12 salt boxes used as drawers in the compartments.
⅓ lb. 8-penny nails to be used in the construction of the cabinet.
12 round-head screws to be used as knobs.
Sandpaper and stain.
DIMENSIONS:
_Body_: 1 box 4¾” deep × 13¼” wide × 18¼” long.
_Shelves_: 4 pieces ⅜” thick × 4¾” wide × 12¼” long.
_Drawers_: 12 salt boxes, 4” × 4” × 4”.
[Illustration]
[Illustration]
DIRECTIONS:
Remove the sides from the box, making them the exact length
of the inside of the box. Draw a line across the bottom and
the ends of the box about 2” from the edge of the sides. Nail
the sides to the bottom and the ends of the box about 2” from
the edge of the sides, with outside faces on pencil line.
Plane and sandpaper the edges until they are smooth. Nail the
shelves in at equal distances apart to make four compartments of
equal size. Place three of the salt boxes in each compartment.
Sandpaper, stain, and polish.
IRONING BOARD
This ironing board is a very great step saver. It is always ready and
in place. It is fastened to the wall at the most convenient place and
adjusted to suit the one who is to use it. When not in use it can be
folded up and hinged against the wall out of the way. The leg is hinged
to the ironing board and falls into position when the board is lifted.
Skirts may be easily ironed without changing the position of the leg.
MATERIALS:
8’ of pine.
3 3” plain steel (butt) hinges.
2½ doz. 1½” No. 12 flat-head screws.
2 yds. of white cotton flannel.
2½ yds. unbleached muslin.
2 pieces of cotton tape.
DIMENSIONS:
1 piece 1” thick × 14” wide × 3’ long to be used as top of board.
1 piece 1” thick × 4” wide × 10” long to be used as a board strip.
2 pieces 1” thick × 2” wide × 4” long to be fastened to the wall
to hold the board in position.
1 piece 1” thick × 4” wide × 14” long to be used as a wall strip.
1 piece 1” thick × 4” wide × 4’ long to be used as brace for board.
1 piece 1” thick × 4” wide × 8” long to be used as brace support.
DIRECTIONS:
Plane the top of the board (1” × 14” × 3’) on the smoothest
side. With a radius of 4½” lay out a semi-circle at the middle
of one end of the board as shown in illustration. This may be
done with a compass or with a string and pencil. Make the other
end of the board square with one edge. Two feet from each end
make a mark on each edge and draw a straight line from each of
these marks tangent to the semi-circle. Saw along these lines,
smoothing the edges with the plane. Fasten the wall strip (1”
× 4” × 14”) to this top with 2 No. 3 (butt) hinges. Bore 3 ¼”
holes through the board strip (1” × 4” × 10”) and fasten it to
the bottom of the top at a distance of 34” from the wall strip.
The brace (1” × 4” × 4’) is fastened to the board strip with
one No. 3 (butt) hinge. ¾” holes are bored through the wall
strip and it is fastened at a convenient height to the wall
with 3 flat-head screws. After boring 3 ½” holes through the
brace support (1” × 4” × 8”) it is screwed to the wall with 3
flat-head screws. Place this support directly below the wall
strip and at such a distance from it to make the board level
when the brace is in position. Bore 2 ¼” holes in one of the
pieces measuring 1” × 2” × 4”, and one hole through the other
piece. Fold the board up against the wall and fasten the piece
with the two holes to the wall just a little to one side of the
board and 2’ above the wall strip. The other piece with one hole
is fastened to this piece to hold the ironing board in position.
[Illustration]
The covering may be made of cotton flannel or an old blanket.
Allow 2” on the sides and the end to be turned under after it
has been cut the shape of the board. This must be tacked
firmly and smoothly on the board. The ironing sheet may be made
of unbleached muslin or an old sheet. This is also cut the shape
of the board, allowing 4” on the sides and end for the hem.
Attach pieces of tape to the opposite sides about 10” apart to
tie the sheet on the board.
JELLY STRAINER NO. 1
An old chair is generally used to hang the jelly bag over while the
juice is dripping. As a substitute the device shown in the following
illustration is suggested as being more convenient and sanitary in
every way. It not only provides a place for the bag to hang, but it
also has a shelf on which the pan sits to catch the drippings from
the bag. The legs are adjustable; hence it is easily taken apart and
kept in a small space. This makes the strainer especially convenient
to the Canning Club Agent as she goes her daily rounds teaching the
housekeepers the art of jelly-making. It can be easily made at home and
at a little cost.
MATERIALS:
3’ poplar.
12 No. 10 screws, 2¼”, to fasten the adjustable legs to the
shelves.
8 No. 9 screws, 1”, to fasten braces to the top of strainer,
1 yd. white flannel for the jelly bag.
1 piece of white tape to make loops on bag.
[Illustration]
[Illustration]
DIMENSIONS:
_Legs_: 4 pieces 1½” thick × 1½” wide × 31½” long.
_Shelves_: 4 pieces 1” thick × 1½” wide × 7” long to make the
upper shelf.
1 piece 1” thick × 15” wide × 15” long for lower shelf.
_Braces_: 4 pieces 1” thick × 2½” wide × 3” long to be cut into
4 equal triangles.
DIRECTIONS:
Bevel the tops of all 4 of the legs at an angle of 45°. Make the
upper shelf of the 4 pieces measuring 1” × 1½” × 7”. Measure
2¼” from the tops of the 4 legs and screw the upper shelf to
the legs at these points. A solid piece of wood with a hole in
the center may be used in making this shelf. Support this upper
shelf by screwing the four triangular braces (1” × 2½” × 3”)
in the corners of the shelf. Use the 8 1-inch No. 9 screws for
this purpose. Saw the lower shelf out 1½” on each corner and
screw it on the legs at a distance of 9” from the bottom of the
legs. Sandpaper but do not stain. Take a piece of flannel of the
desired size and make the jelly bag in the shape of a triangle.
Sew a loop of tape at each corner to hang the bag over the posts.
JELLY STRAINER, NO. 2
While this jelly strainer is unique and useful in its construction
it is not adjustable. It is made of poplar at a minimum cost. Around
the top edge are arranged little brass hooks. These are put at equal
distances apart. At the lower end of the trough two plugs are put, one
above the other, through which the jelly juice flows out into a pan
placed beneath the plugs.
[Illustration]
The jelly bag is made of an oblong piece of flannel with ivory rings
sewed around the edges so as to hang the bag on the brass hooks around
the top of the frame.
MATERIALS:
4’ of poplar.
4 No. 9 screws, 1½”, to fasten handles on the sides.
16 No. 10 screws, 2”, to fasten ends on the sides.
5 No. 10 screws, 1¼”, to fasten the sides together at the bottom.
14 brass cup hooks arranged around the top edges.
14 white ivory rings to be sewed on jelly bag.
1 yd. white flannel for jelly bag.
DIMENSIONS:
_Sides_: 2 pieces 1” thick × 12” wide × 15½” long.
_Ends_: 2 pieces 1” thick × 12½” wide × 17½” long.
_Handles_: 2 pieces 1” thick × 2½” wide × 4” long.
_Plugs_: 2 pieces 1” thick × 1” wide × 3” long.
DIRECTIONS:
Saw the two end pieces according to the illustration. Measure
6½” from the bottom of each end and cut them out ¼” to fit sides
(1” thick) placing the sides ¾” from the outer side of the end
pieces. Measure equal spaces from each side of the ends and put
the handles 1½” from the top edge. Bore two holes ¾” in diameter
near the bottom of the end to fit the plugs. Bevel the two
sides (1” × 12” × 15½”) at the bottom so as to make a tight and
neat joint. Screw the end pieces to the sides. Screw the brass
cup hooks at equal distances apart around the top edge of the
strainer.
[Illustration]
DISH DRAINER
The work of dish-washing is greatly reduced by the use of a dish
drainer. The dishes are carefully washed and arranged in the drainer,
and boiling water poured over them. When they are dry, they can be put
away or allowed to stand with a clean cloth thrown over them until
ready to use.
This dish drainer resembles a box in shape, put on legs, with slats
placed inside at equal distances apart, making the compartments to hold
the dishes. The space in front is made a little larger to accommodate
the irregular dishes. An experienced housewife will know that glassware
and silverware cannot be dried by this method. A hole is made in one
corner of the drainer through which the water drains off into a pail
which is kept under the corner.
MATERIALS:
16’ of white pine.
½ lb. of 4-penny nails for nailing slats in box.
½ lb. of 8-penny nails for nailing box on the legs.
4½’ of sheet zinc to cover the inside of drainer.
4” of half-galvanized pipe for drainage tube.
1 drainage pail.
Sandpaper.
1 can of white paint.
1 can of white enamel.
DIMENSIONS:
_Bottom_: 1 piece 1” thick × 24” wide × 26” long.
_Sides_: 2 pieces 1” thick × 8” wide × 26” long.
2 pieces 1” thick × 8” wide × 24” long.
_Legs_: 4 pieces 1” thick × 4” wide × 36” long, for back legs.
4 pieces 1” thick × 4” wide × 35” long, for front legs.
_Slats_: 2 pieces ¼” thick × 1” wide × 24” long.
6 pieces ¼” thick × 1” wide × 26” long.
DIRECTIONS:
Make a pine box which is 8” deep and 24” × 26” long. The joints
must be laid in white lead in order to make the drainer water
tight. Nail 2 slats ¼” thick × 1” wide × 24” long down flat
from the front to the back of the box at the outer edge. These
are used as supports for the other crosswise slats and also
allow the water to run under the slats. Nail 4 slats on these
supports, beginning 3¼” from the back of the box and making a
distance of 3¼” between each slat. This will leave a 9” space in
front of the box for the irregular dishes. The front legs are
made of the four pieces 1” thick × 4” wide × 35” long, and the
back legs are 1” thick × 4” wide × 36” deep. This slant provides
for the drainage. The drainer should be tipped a little to the
corner in which the drain pipe is placed. If zinc is to be used
for lining, it must be done before the slats are put into the
box.
[Illustration]
DISH RACK
A rack made of poplar, with several compartments to accommodate dishes
of different sizes.
The large platters are put in the largest upright spaces, the dinner
plates being arranged in the middle-sized spaces, with the smaller
plates and saucers in the top spaces. It may be placed at a convenient
place in the kitchen or dining room so as to save the housekeeper
unnecessary steps. Mortise and tenon joints will make a more
substantial rack but these are not necessary. The parts may be nailed
together. After joining the parts together, sandpaper, paint white and
enamel.
MATERIALS:
6½” poplar.
12 No. 6 nails to nail on the top.
45 No. 44 box nails for nailing on upright pieces.
50 No. 16 wire brads, ¾”, for nailing tenons in mortise.
2 No. 9 screws, 1½”, to screw the base on the rack.
Sandpaper for dressing the rack.
1 pt. white paint.
1 pt. enamel.
DIMENSIONS:
_Top_: 1 piece ¾” thick × 4½” wide × 33” long.
2 pieces ¾” thick × 1½” wide × 30” long.
_Bottom_: 2 pieces ¾” thick × 1½” wide × 30” long.
1 piece 1” thick × 2½” wide × 12” long for base.
_Middle_: 2 pieces ¾” thick × 1½” wide × 21” long.
_Ends_: 2 pieces ¾” thick × 1½” wide × 24” long.
_Crosspieces_: 2 pieces ¾” thick × 1½” wide × 3” long to be used
as top of rack.
2 pieces ¾” thick × 3” wide × 3” long to be used as bottom of
rack.
_Upright pieces_: 16 pieces ½” thick × ½” wide × 26” long to be
used as side pieces 8 on each side.
2 pieces ¾” thick × 1½” wide × 20½” long.
[Illustration: _Dish Rack_]
DIRECTIONS:
Mortise the two end pieces ¼”, to fit tenon. Nail the two
crosspieces, measuring (¾” × 1½” × 3”) to them. Make ¼” mortises
on the two top pieces (¾” × 3” × 3”). These mortises are made 3”
from the end and the two pieces nailed to crosspieces. Screw on
the bottom board (1” × 2½” × 12”) with 1½” No. 9 screws. Mortise
the 4 top and bottom pieces (¾” × 1½” × 30”) ½” from the top
and bottom and nail them lengthwise on the rack. The two middle
pieces (¾” × 1½” × 21”) are mortised and nailed 11” from the top
edge of the bottom piece. The upright pieces (¾” × 1½” × 20½”)
are nailed 9” from the left side. Nail the eight upright pieces
(½” × ½” × 26”) on each side with No. 4 box nails. The top piece
(¾” × 4½” × 33”) is nailed on the top of the rack. Sandpaper,
paint and enamel.
[Illustration]
COAL BOX
The construction of this box is both simple and convenient, and it
requires little space in the room to accommodate it. There are four
compartments in it. The back is divided equally to provide places for
the kindling and paper; the front space is used for coal, and while it
makes it more durable to line it with metal, this is not necessary.
There is a narrow opening in the front in which the cleaning materials
are kept--polish, brush, and stove rags. Stain or paint will make the
coal box more attractive.
MATERIALS:
27½’ of poplar.
3 pairs of 1½” (butt) hinges.
24 ¾” No. 8 screws for hinges.
2 lbs. 5-penny box nails.
3 screen door handles.
1 iron door button.
4 castors.
5 lbs. sheet metal.
DIMENSIONS:
_Top_: 1 piece 1” thick × 1’ 9¾” wide × 2’ 1½” long to be used as
level top.
_Front_: 1 piece 1” thick × 1’ 7” wide × 2’ 1½” long for the
slanting front.
_Bottom_: 1 piece 1” thick × 1’ 11½” wide × 2’ 10” long.
_Back_: 1 piece 1” thick × 2’ 1” wide × 1’ 11½” long to be used
as the back of the box.
_Ends_: 2 pieces 1” thick × 2’ 2” wide × 3’ long.
_Partitions_: 1 piece 1” thick × 21” wide × 1’ 11½” long to be
used as the partition in the back.
1 piece 1” thick × 2’ 2” wide × 1’ 11½” long to be used as the
slanting partition in the bottom of the coal box.
_Supports_: 1 piece ½” thick × ½” wide × 1’ 11½” long to be used
as a support at the back of the opening in the box to hold
door in place.
_Drawer_: 1 piece 1” thick × 1’ 1½” wide × 2’ 1½” long for the
front of the drawer.
1 piece 1” thick × 5” wide × 1’ 11½” long for the back of the
drawer.
1 piece 1” thick × 10” wide × 1’ 11½” for the top of the drawer.
[Illustration:]
DIRECTIONS:
Measure 1’ 9¾” from the back of the two end pieces (1” × 2’ 2” ×
3’). Cut the corners off from this point to make a slant which
will fit the door 1’ 7” long. Nail the back (1” × 1’ 11½” × 2’
1”) to the two end pieces at the straight edge. The bottom
piece (1” × 1’ 11½” × 2’ 10”) is then nailed to the back and
sides. Cut out a 4” × 1’ 11½” opening in the front piece (1”
× 1’ 11½” × 2’ 1½”) for the drawer and then nail the front to
the sides and bottom. Take the piece which has been cut out and
hinge it to the opening as shown in the illustration. Nail the
back and top partitions in this opening before the slanting
partition which divides this division from the coal bin is
put in. Measure 9” from the back of the coal box and put the
straight partition (1” × 21” × 1’ 11½”) in by nailing it to the
bottom and sides of the coal box. Then the slanting partition
(1” × 2’ 2” × 1’ 11½”) is nailed to the bottom and front edge
of the box as shown in the illustration. Cut an opening (9” ×
1’ 11½”) in the top (1” × 1’ 9¾” × 2’ 1½”) and then nail top on
the box, using the piece which is cut out for the door to the
opening. Hinge this piece on with one pair of 1½” (butt) hinges.
The door support (½” × ½” × 1’ 11½”) is nailed on the inside
of the back of the box. Bevel the piece (1” × 1’ 7” × 2’ 1½”)
for the slanting door. It must fit each edge as shown in the
illustration. Hinge this door at the upper edge of the top with
one pair of 1½” (butt) hinges. One screen door handle is put on
each opening to lift them. The four castors are placed on the
bottom of each corner of the box to make it more easily moved
about. Stain or paint the coal box.
[Illustration]
A HOME-MADE COOK STOVE DRIER
This apparatus is designed to use on a wood or coal stove, an oil
stove, or a gas range. It can be easily and inexpensively made at home.
MATERIALS:
12’ of poplar for the frame.
14 lbs. black sheet steel, 27 gauge, to cover frame.
9 sq. ft. galvanized wire cloth about ¼” mesh for shelves.
½ lb. 4-penny nails.
1 hook and eye to fasten door.
2 prs. small hinges for the door.
DIMENSIONS:
_Frame_: 4 pieces 1¼” × 1¼” × 23”.
_Sides_: 4 pieces 1¼” × 1¼” × 21”.
_Front_: 2 pieces 1¼” × 1¼” × 11”.
_Back_: 2 pieces 1¼” × 1¼” × 11”.
_Supports_: 6 pieces 1” × 2¼” × 23½”.
_Trays_: 12 pieces ¾” × ¾” × 20½”.
12 pieces ¾” × ¾” × 10½”.
DIRECTIONS:
The frame consists of four wooden posts (1¼” × 1¼” × 23”); four
side pieces (1¼” × 1¼” × 21”); two front pieces (1¼” × 1¼” ×
11”); and two back pieces (1¼” × 1¼” × 11”). To the posts are
lightly nailed on each side six strips (1” × 2¼” × 23½”). These
pieces serve as supports for the drying racks. The corners are
notched out as indicated in the drawing to allow the strips to
extend out to the outer wall of the drier.
For each side use a sheet of light weight sheet steel (23½” × 23”);
for the back a sheet (13½” × 23”); for the top a sheet (13½” ×
23½”). In the top piece an opening about 3” × 10” is cut about
four inches from the back edge to permit the escape of moist
air. It may be found at times that this ventilating opening is
too large. Then it may be partially closed by placing over it a
tin pan or other vessel.
For the bottom a sheet 13½” × 23½” is used. This sheet is
thoroughly perforated with holes to admit the warm air. Another
piece of sheet steel (A on the drawing) (7½” × 17½”) is provided
to make the heat spread more evenly. This piece rests on wires
above the bottom of the drier. These wires are put through small
holes punched in the side sheets (see B on drawing).
The door is made of heavier gauge sheet steel (13½” × 23”).
The legs are made of four pieces of sheet steel bent on an angle as
indicated in the drawing.
All the sheet steel parts may be tacked on the frame but the door,
which is secured by hinges.
The frames of the six trays are made of ¾” wood 10½” wide and 20½”
long. Make the bottom of the trays of wire cloth (20½” × 10½”).
This is tacked on the underside of the frame of the trays.
By referring to the drawing it will be observed that the bottom tray
is shoved back as far as it will go; the next tray above is pulled as
far front as the door will admit; the next tray is shoved back and so
on with each tray shoving one to the back and pulling the other to the
front. The object of this arrangement is to allow the heat to pass
over and around the ends which causes a more rapid movement of the air
current. This is more important in drying than the heat.
It may be necessary to shift the trays by putting the top one on the
bottom and the bottom one on the top during the drying process so as to
dry the products more uniformly.
[Illustration]
[Illustration: Home-made driers ready for use. (Courtesy of Peabody
College for Teachers, Nashville, Tenn.)]
WOOD BOX
(MADE FROM DRY GOODS BOXES)
[Illustration]
What an unsightly spectacle does a wood pile by the stove, on the
porch, or in the corner of the room present! It is a place of refuge
for all trash, such as old papers and rags. This not only adds to
the untidiness of the room or porch, but it makes extra work for the
already overworked woman. The wood box made of old dry goods boxes
should appeal strongly to the home. It can be kept by the stove or on
the porch or in some convenient place to be reached, and to be filled
by the man before he goes to his daily work. A lid will not only cover
up the contents of the box, but it will serve as a comfortable seat to
be used while preparing the meal.
MATERIALS:
1 packing box, 24” deep × 23½” wide × 32” long.
1 pair 2” (butt) hinges with ⅝” screws to fasten on top.
¼ lb. 8-penny nails to make box.
Sandpaper and stain.
DIMENSIONS:
_Body_: 1 box 24” deep × 23½” wide × 32” long.
_Top_: 1 piece ¾” thick × 18” wide × 32” long.
_Legs_: 4 pieces ¾” thick × 2” wide × 28¾” long.
4 pieces ¾” thick × 2½” wide × 28¾” long.
_Cleats_: 2 pieces ½” thick × 3” wide × 15” long.
_Hinge Strip_: 1 piece ½” thick × 3” wide × 29” long.
DIRECTIONS:
Make the legs 4” longer than the depth of the box after the
cover has been removed, and nail them on the box. Make the cover
2” wider and 2” longer than the outside length and width of the
box. Place each cleat about 3” from the end of the cover and
nail on the cover. Hinges are put 5” from each end of the box.
Sandpaper, stain and polish.
[Illustration]
FIRELESS COOKER
There are many advantages in having a fireless cooker in the home. It
not only saves time and fuel but keeps the woman from standing over
the hot fire, and there are many foods that are better when cooked
at a lower temperature. The principle of the fireless cooker is to
retain the heat by boiling the food in a vessel with a tight cover and
placing it in the cooker in the same vessel, thus keeping the heat from
escaping. An outside container may be made to accommodate one or more
cooking vessels. A cheap but efficient fireless cooker may be made of a
tightly built wooden box, a barrel, or a tin lard can as shown in the
illustration. If the outside container is of wood it must be lined on
the inside with asbestos or heavy paper to keep out the air.
The nest may be a galvanized or tin bucket of a size which will admit
of three inches of packing between the outside container and the nest.
The sides and bottom of the nest are covered with asbestos to prevent
the scorching or the burning of the packing.
The packing must be of some material through which the heat cannot
easily escape. Cork, sawdust, excelsior, hay, or shredded newspaper may
be used to an advantage. Three inches of this packing is put tightly in
the bottom of the outside container and around the sides to fill in the
space between the outside container and the nest.
A four-inch space is left at the top of the fireless cooker in which
a cushion made of unbleached cotton or some other material is stuffed
with the packing and placed to make the cooker air-tight. Cut two
circles out of the unbleached cotton and a three-inch straight piece
to join the circles together. A hot soapstone, stove plate or brick is
placed in the bottom of the nest before the food vessel is placed in
the fireless cooker. The food vessel may be any cooking utensil with a
top that will fit in the nest after the soapstone has been put in. Cut
a circle of tin or cardboard to fit top of inside of cooker with an
opening the size of the nest. This gives a good finish to the top of
the fireless cooker and preserves the packing.
[Illustration]
[Illustration: Assembled material for building a fireless cooker. 1,
Outside container; 2, paper for lining; 3, material for packing; 4,
inside nest; 5, cooker vessel; 6, soapstone; 7, paste; 8, tape; 9,
cardboard; 10 muslin for cushion; 11, stain; 12, a finished cooker; 13,
top to inside nest]
MATERIALS:
1 lard can 18” × 24”.
1 lard can 12” × 15”.
4 lbs. excelsior.
1 yd. asbestos.
¾ yd. unbleached cotton.
1 soapstone.
1 sheet cardboard.
DIMENSIONS:
_Outside Container_: 18” × 24”.
_Nest_: 12” × 15”.
_Cooking Vessel_: 11½” × 13”.
DIRECTIONS:
Place 3” of excelsior in the bottom of the outside container
(18” × 24”) and pack it down tightly. Cover the bottom and sides
of the nest (12” × 15”) with asbestos. Then place nest in the
outside container holding it in place while 3” of packing is
put tightly between the outside container and nest. Cut the
cardboard circle to fit inside of the top of outside container
with an opening to fit the top of the nest and put on top to
give a good finish and to preserve the packing. Make the cushion
for the top of the unbleached cotton by cutting two circles with
3” strip to join them together. Then pack the cushion tightly
with the same packing. Enamel the cooker.
[Illustration]
[Illustration: Any convenient box may be used and any can of convenient
size, such as a lard can, etc. The cans should be wrapped with about 4
or 5 layers of asbestos paper. The space around the cans should be at
least 2 inches, and filled with straw or wood shavings, etc. The top of
the cans should be covered with a pad filled with straw or shavings,
etc.]
CHAPTER II
=DINING-ROOM CONVENIENCES=
ROLLER TRAY WAGON
An efficient and convenient table placed on casters and wheels and
comprising a china closet, drawer for silverware, serving table, and
roller tray all in one. This device is invaluable to the housekeeper
who does her own work. It saves her many steps in the preparation and
the serving of her meals. While she is entertaining at a luncheon, it
takes the place of a maid, since the refreshments can be prepared,
arranged on the wagon, and rolled out at the appointed time. The prices
of a tea wagon made in wicker or some expensive wood are very high, but
one like the following illustration can be made at a nominal cost, or
it can be made of dry goods boxes for even less.
MATERIALS:
26’ white pine.
1 piece of jack chain No. 14, 18” long, to support top.
1 pair 1½” (butt) hinges to hold top.
12 No. 5 screws, ¾”, to fasten hinges.
½ lb. 5-penny box nails.
2 brass hand bolts to fasten on drawer.
8 No. 10 screws, 2½”, to fasten legs to bottom shelf.
2 furniture casters to put on legs.
2 swivel or baby carriage wheels.
DIMENSIONS:
_Top_: 1 piece 1” thick × 16½” wide × 26½” long.
_Sides_: 2 pieces 1” thick × 5” wide × 33½” long, for front and
back of body.
_Ends_: 2 pieces 1” thick × 5” wide × 13” long, for top of frame.
_Handles_: 2 pieces 1” thick × 1” wide × 15” long.
_Bottom_: 1 piece 1” thick × 13” wide × 24½” long.
_Legs_: 4 pieces 1½” thick × 1½” wide × 32” long.
_Ends_: 2 pieces 1” thick × 3½” wide × 12” long, allowing 1” on
each end for tenon.
_Drawer_: 1 piece 1” thick × 1½” wide × 23½” long, for foundation
of drawer.
[Illustration]
_Cleats_: 2 pieces 1” thick × 1” wide × 14” long, to support the
drawer.
1 piece 1” thick × 2½” wide × 23½” long, to be used as front to
drawer.
1 piece ½” thick × 2½” wide × 23½” long, to be used as back of
drawer.
2 pieces ½” thick × 2½” wide × 13½” long, to be used as side of
drawer.
1 piece ½” thick × 15” wide × 23½” long, to be used as bottom
of drawer.
1 piece ½” thick × 2½” wide × 3½” long, to be used as partition
in drawer.
_Shelf_: 1 piece 1” thick × 15” wide × 26½” long, to be used as
bottom of shelf.
_Braces_: 2 pieces 1” thick × 1½” wide × 12” long, to support ends
of shelf.
_Brackets_: 2 pieces 1” thick × 8” wide × 8” long, to be used as a
support for wheel.
[Illustration: Roller tray wagon, including compartment for china and a
drawer for silver and linen]
DIRECTIONS:
Take the 2 sides (1” × 5” × 33½”) and round each end in the
shape of a half circle, boring a 1” hole in each end of side
piece to hold handles (1” × 1” × 15”). Fit bottom on inside of
box and nail it. Mortise 3½” from the top of the legs to fit
cross pieces, 1” × 3½” × 12”. Make a ¼” mortise on the legs 9”
from the bottom for the support of the bottom shelf. Measure
2½” from the top of the leg to put tenon for the front drawer
support. Construct the opposite end of the table in the same
way. The upper top of table, showing the lid and handle, should
be fastened to top after the table is made. In making the frame
for the drawer, 2½” deep × 13½” wide × 23½” long, nail the front
and back to the sides. Then nail the bottom of the drawer to
the inside of this frame with one partition nailed crosswise
the center of the drawer. Place handles on the front of the
drawer about 3” from each end. Screw on the 2 pieces placed 9”
from bottom of the leg, with 2½” No. 10 screws. Cut the bottom
shelf out 1½” at each corner, fit to the legs, and screw. This
shelf must be stationary. Brackets, 1” × 8” × 8”, are screwed
on at one end of the shelf to be used as supports to which the
wheels are fastened. The drawer may be used for silverware
and to keep the linen. The side used for silverware should be
lined with felt or outing. The table should be well dressed by
sandpapering, staining, and polishing it. Do not varnish it
because this does not make so attractive a table as the mission
stain.
SIDEBOARD
(MADE OF DRY GOODS BOXES)
A unique article made of dry goods boxes, which may be used in the
dining room as a sideboard or in the kitchen as a cupboard. Two dry
goods boxes are joined together to make the lower section, one end
on each box being removed to be used as shelves in the sideboard.
The upper section with its three shelves is made from pieces of
other boxes. On two of the shelves brass hooks are arranged at equal
distances apart, on which the cups hang. A groove may be made under
the lower shelf and on the top shelf, in which the small plates and
saucers rest. The two drawers, made according to dimensions and out
of pieces of boxes, can be lined with felt or outing flannel to hold
the silverware. Attractive curtains may be made of some suitable
material and hung in front of the upper section. This is especially an
interesting problem for boys in a school to work out.
MATERIALS:
3 large boxes for lower and upper sections of sideboard.
3 small boxes to be used for drawers.
2 pairs 1½” (butt) hinges to fasten doors.
½ lb. 6-penny nails to build sideboard.
2 metal knobs to be used on lower doors.
24 brass cup and saucer hooks.
2 hand bolts to be used on front of drawers.
Sandpaper and stain.
DIMENSIONS: Lower Section:
_Body_: 2 boxes 13” deep × 12½” wide × 26” long.
_Shelves_: 2 pieces 1” thick × 12” wide × 24” long.
_Cleats_: 4 pieces ½” thick × ¾” wide × 12” long, to be used under
the shelves.
_Doors_: 4 pieces ¾” thick × 2” wide × 26” long, to be used for
upright pieces.
4 pieces ¾” thick × 2” wide × 8” long, to be used as crosspieces.
2 pieces ½” thick × 9” wide × 23” long, to be used as panels.
_Legs_: 4 pieces ½” thick × 2¾” wide × 36” long.
4 pieces ½” thick × 2½” wide × 36” long.
[Illustration]
Upper Section:
_Body_: 1 box 5” deep × 18” wide × 26” long.
2 small boxes 5” deep × 12” wide × 18” long.
_Drawer_: 1 box 5” deep × 18” wide × 24” long.
DIRECTIONS:
Boxes which can be most easily converted into the desired
sections must be selected. Two boxes (13” × 12½” × 26”) are
joined together to form the body of the lower section of the
sideboard. Remove the ends of the boxes, to be used as shelves,
using the side of a larger box for the top of this section.
The shelves are fastened in by 4 cleats (½” × ¾” × 12”) nailed
crosswise the partition and the sides of the section. Four
strips (½” × 2¾” × 36”) and four strips (½” × 2¼” × 36”) are
taken from the third box to make the legs of the cabinet. The
doors are fastened on with hinges, using two metal knobs in
front of the doors to open them. The foundation of the upper
section is made of a box (5” deep × 18” × 26”). The three
crosspieces used as shelves are made from the two small boxes
(5” × 12” × 18”). Make the drawer of a box (5” × 18” × 24”),
putting a partition through the center of the box and on the
inside if two drawers be desired. Place two hand bolts on the
front of the drawer. Sandpaper, stain, and polish the sideboard.
[Illustration]
SCREEN
[Illustration]
A screen is useful in many ways in the home. It adds a great deal to
the appearance of a bedroom. By putting it around the bed one may often
avoid draughts. In the dining room it is indispensable in the front
of a serving table while the meal is going on. The illustration above
shows a two-panelled screen which may be easily made in the home, or
it furnishes good material for a woodwork problem to be used in the
school. It is made of oak and covered with burlap. By adding to the
number of pieces the third panel may be made with ease.
MATERIALS:
3 feet of oak.
¼ lb. 8-penny nails to be used in making frame.
3 1” (butt) hinges, with screws, to join panels together.
1 box of brass-headed tacks to fasten burlap to frame.
Sandpaper and stain.
3½ yds. burlap to cover panels.
DIMENSIONS:
_Frame_: 4 pieces 1” thick × 1” wide × 5’ long, to be used for
upright pieces.
6 pieces 1” thick × 1” wide × 2’ long, to be used for crosspieces.
DIRECTIONS:
Measure and saw the pieces according to required dimensions. Cut
the joints and nail the three crosspieces to the two upright
pieces. Make the other panel in the same way and join the two
together with the three hinges. Sandpaper, stain, and polish the
frame. After it has dried thoroughly, cover it with the burlap
on the outside, tacking this on with the brass-headed tacks.
CHAPTER III
=PORCH EQUIPMENT=
ICELESS REFRIGERATOR NO. 1
Country homes without ice houses and too far from town to have access
to manufactured ice may have an iceless refrigerator as a good
substitute. This convenience comprises a simple wooden frame with a
covering of canton flannel, burlap, Indian-head cloth or linen crash
made to fit so that little air is admitted into it. Wicks made of the
same material as the cover are tacked on top of each side of the cover
and extend over into the pan of water sitting on top of the frame. This
water is taken up by the wicks and carried down on the sides of the
cover by capillary attraction when evaporation takes place, drawing
the heat from the inside and lowering the temperature. The more rapid
the evaporation, the lower the temperature. Tests have shown that if
the refrigerator is kept in a place where the air circulates around it
freely, a temperature of 50 degrees Fahrenheit may be obtained.
MATERIALS:
40’ of white pine.
1 pair of 1½” (butt) hinges to fasten the door.
1 2” gate hook to close screen door.
½ lb. 5-penny nails to build frame.
3½ yds. wire screening to cover frame.
4 sq. ft. sheet zinc to make shelves.
1 pt. white paint.
1 can white enamel.
1 square pan for top of refrigerator.
1 large pan for bottom.
Sandpaper.
2 cards of snap hooks and eyes to put on cover.
5 yds. white canton flannel.
DIMENSIONS:
_Frame_: 4 pieces ½” thick × 3” wide × 48” long, for upright
pieces.
16 pieces 1” thick × 1” wide × 16” long, to be used as
crosspieces for top, bottom, and shelves.
_Door_: 2 pieces ½” thick × 3” wide × 39” long, for upright
pieces.
2 pieces 1” thick × 1” wide × 16” long, for crosspieces.
[Illustration]
DIRECTIONS:
Make the frame 3½’ high with twelve crosspieces tacked to the
four posts, nailing the first 4 strips 9” from the bottom of
the frame, and the remaining 8 strips about 11” apart. An 18½”
square frame is made of wood and nailed on top of the posts. The
corners of this square are mitered or lapped over and tacked
together. Use a biscuit pan to fit in top of the square to hold
the water. The whole refrigerator should stand in a larger pan
which catches the drippings from the cover and keeps away the
insects. The screen door is made 39” long × 16” wide, which is
joined to the frame with hinges and fastens with a hook. Three
movable shelves with perforations in them are made of zinc.
Cover the whole frame with wire screening to protect it from the
flies. When the frame is finished it should be painted white
and enameled. This will permit of its being washed every day. A
covering of white canton flannel is made to fit the screen, with
the smooth side out, care being taken that the cover comes to
the lower edge of the frame. The wicks are made half the width
of the sides and tacked on the top edge of each side. These
must be long enough to extend 3” over into the water. Strips of
canton flannel 2” wide are tacked all around the sides and the
top of the frame, and the eyes are sewed on these. White tape
may be used for this purpose if more convenient. Sew one row of
hooks on the edge of the covering near the latch and the other
just opposite the opening, with the hem to extend far enough
over on each side to cover crack at the edge of door. This
permits the door to be opened without unfastening the hooks,
keeping out the warm outside air and at the same time retaining
the cool air inside the refrigerator. Hook the covering around
the top also. Place the refrigerator in a shady place where the
air will circulate around it freely. Keep the wicks in a supply
of fresh water in the top pan. The water is taken down the sides
by capillary attraction, and when evaporation takes place the
heat is taken from the inside thereby lowering the temperature.
[Illustration]
[Illustration:
First View Second View Third View
Iceless refrigerator]
ICELESS REFRIGERATOR NO. 2
Another type of iceless refrigerator which appears more crude can
be made at a cost of $1.80. In this a cotton sack is used for the
covering. This refrigerator has proved more satisfactory than one would
suppose. The butter and milk from several cows has been kept in a model
of this type at ten degrees cooler than the outside air. It might be
well to use cotton flannel for the covering instead of ducking because
when the cloth is wet evaporation takes place more rapidly.
MATERIALS:
24½’ yellow pine.
5½ yds. canton flannel.
15 10-penny nails.
1 No. 2 galvanized tub.
DIMENSIONS:
_Stem_: 1 piece 2” thick × 4” wide × 5’ long.
_Shelves:_ 2 pieces 1” thick × 32” wide × 32” long.
1 piece 1” thick × 20” wide × 20” long.
_Supports_: 2 pieces 2” thick × 4” wide × 18” long to be used as
braces for the foundation.
_Cleats_: 4 pieces 2” thick × 4” wide × 30” long to support shelves.
[Illustration]
DIRECTIONS:
Nail the piece (2” × 4” × 18”) on the side of the stem making it
even with the bottom piece. Saw a 2” base out on the side of the
stem and nail the other piece measuring 2” × 4” × 18”. Measure
25” from the bottom of the stem and nail on 2 cleats to support
the shelf. Cut space in the center of piece (1” × 32” × 32”)
large enough to fit the stem and nail it to the cleats, thus
making the first shelf. From this point measure 20” and nail 2
cleats on the stem to support the second shelf (1” × 32” × 32”).
Measure 13” from the top of the stem and nail on shelf (1” ×
20” × 20”) after cutting an opening (2” × 4”) in the center of
shelf. The curtain is made of 4 widths of the canton flannel
measuring 66” in length with a draw string put at the top and
bottom of the curtain. This makes the refrigerator dust and fly
proof.
UMBRELLA STAND
A good problem to be used in woodwork classes in the school or to be
made by boys in the home. It will be found appropriate and useful in
the reception hall or on the porch. It is built of dry goods boxes,
with a five-cent pan used in the bottom to catch the drippings from the
umbrellas.
MATERIALS:
1 box 9” deep × 12” wide × 30” high.
¼ lb. eight-penny nails to make the frame.
1 small round tin pan to fit in bottom of the stand.
Sandpaper and stain.
[Illustration]
DIMENSIONS:
4 pieces ¼” thick × 2½” wide × 30” long, to be used as upright
pieces.
4 pieces ¼” thick × 2¼” wide × 30” long, to be used as upright
pieces.
6 pieces ½” thick × 3” wide × 12” long, to be used as crosspieces.
6 pieces ½” thick × 3” wide × 11” long, to be used as crosspieces.
_Bottom_: 1 piece 12” thick × 12” wide × 12” long.
[Illustration]
DIRECTIONS:
Make three boxes of the six pieces (½” × 3” × 12”) and six
pieces (½” × 3” × 11”), putting the bottom, 12” square, on the
bottom box to be used as foundation of the frame. Make a hole
in this bottom large enough to hold a round tin pan. This hole
should be cut before nailing the piece on the bottom of the box.
Nail the four long pieces (measuring ¼” × 2¼” × 30”) on the end
of the three boxes, placing the boxes seven inches apart on
the frame. Nail four pieces (measuring ¼” × 2½” × 30”) on the
ends of the boxes to extend one-fourth inch over the first four
strips which were nailed on the boxes. Sandpaper, stain, and
polish.
BLACKING BOX
A necessary and useful home convenience made of a box, with a cover
made in two sections and joined with hinges. It is a time-saver to
the busy housewife who has to go so often in search for blacking and
polish before she can get the children ready for school. It serves as a
reminder to the busy farmer who is disposed to go to town or to church
before giving his shoes a dressing.
[Illustration]
MATERIALS:
1 box.
½ lb. six-penny nails to construct box.
1 pair 1½” (butt) hinges to fasten top.
Sandpaper and stain.
DIMENSIONS:
_Body_: 5¾” deep × 13¾” wide × 14¼” long (inside measurements).
_Top_: 2 pieces ½” thick × 8” wide × 6¼” long.
_Legs_: 4 pieces ⅜” thick × 1⅜” wide × 13¼” long.
4 pieces ⅜” thick × 1¾” wide × 13¼” long.
DIRECTIONS:
Remove the cover from box (5¾” deep × 13¾” × 14¼”) and nail the
legs on, making them seven inches longer than the outside depth
of the box. Nail one half of the cover on top of box, allowing
it to project evenly all round the edge of the box. Fasten the
other half of the cover to this half with hinges. Sandpaper,
stain, and polish.
[Illustration]
TOWEL ROLLER
A towel roller built so simply that any boy on the farm would take
pleasure in working out the problem. It is much easier to keep a clean
towel in the right place when the proper place is provided for the
towel to be kept. This convenience should be a joy to every tired
farmer when he comes in to partake of a meal. Again, the tendency of
all children to throw the towels about the place is a great nuisance
to the housewife. This rack provides that the towel be sewed together
and placed on the roller, which is then slipped into the groove made to
hold it.
[Illustration]
MATERIALS:
3’ of poplar.
¼ lb. 8-penny nails.
Sandpaper and stain.
DIMENSIONS:
_Foundation_: 1 piece ¾” thick × 5” wide × 24” long, to which the
brackets are nailed.
_Brackets_: 2 pieces 5” thick × 5” wide × 5” long.
_Rod_: 1 piece 1¼” thick × 1¾” wide × 24” long.
DIRECTIONS:
The brackets are made any desired shape, with a hole a half-inch
in diameter bored in the centre of each piece. A slit is cut
in one bracket from the hole to the top for the end of the rod
to slip in and out. Round the piece (1¼” × 1¾” × 24”) for the
rod. At each end cut a tenon one inch in diameter. Nail the end
pieces to the board (¾” × 5” × 24”). Insert the rod into the
hole in the one end piece and slip it into the slit at the other
end. Sandpaper, stain, and polish.
PORCH SWING
An inexpensive mission style swing made of oak with space long enough
for two to sit in and broad enough to be used for lounging purposes. A
pad made of burlap and stuffed with an old discarded quilt will add to
the comfort of the swing.
DIMENSIONS:
_Frame_: 4 pieces, ¾” thick × 3” wide × 43” long for rails in frame.
2 pieces, ¾” thick × 3” wide × 22” long for ends of frame.
_Posts_: 2 pieces, 1½” thick × 2” wide × 19” long for front posts.
4 pieces 1½” thick × 2” wide × 23½” long for arms and back posts.
_Slats_: 14 pieces ¼” thick × 3” wide × 14” long for back and end slats.
16 pieces ½” thick × 3” wide × 20” long for slats in seat.
_Cleats_: 2 pieces ½” thick × 2” wide × 48” long.
DIRECTIONS:
Mortise the end posts for the back and the front, also arm
posts. Mortise the back and front and end rails of the frame to
fit the end posts. Nail and glue them into position. Round the
edges of the seat slats and nail to cleats on the front and back
of the frame. Mortise the back and end slats, fitting them into
the rails and frame and fasten with strong glue. Use support
made of iron and fastened to the seat with screws to give
strength to the mortises formed at the arms and front posts. The
chains to suspend the swing are fastened to holes made in these
iron supports. Make the back of the swing first, then the ends
and front, nailing the seat slats in after the glue has fastened
the mortises securely together.
[Illustration]
CHAPTER IV
=MISCELLANEOUS EQUIPMENT=
A DUSTLESS MOP
[Illustration]
A cheap and efficient article for the housewife is a mop made of old
stockings and the handle of an old, discarded broom. This mop may
be used successfully for polished and painted floors as well as for
unpolished floors. It is made by cutting the straw off of a broom which
has worn out. This is cut even with the wires which hold the straw on
the handle. Cover this part of the broom with an old stocking, which is
tacked to the handle securely by sewing it around two or three times
with a double thread. Legs of old stockings are cut twelve inches long
with these strips cut leaving a band two inches wide to sew to the
covering of the broom. Sew them round and round the surface in rows
about an inch apart, until the mop has been made the desired thickness.
Dip the mop into a solution made of one-half a cupful of melted
paraffin and one cupful of coal oil. When the mop is not in use, it
must be wrapped up and kept in a paper bag in order to keep it moist.
FOLDING CANNING TABLE
The table shown in this illustration is made of poplar and designed
especially for the Canning Club agent. It folds up and requires little
space, which makes it convenient to take around during the canning
season. The top is zinc-lined to make it more durable and sanitary.
In the center an opening is made to hold the bucket which catches
the parings from the vegetables or fruits. On the left side is an
adjustable zinc-lined trough to hold the vegetables or fruits while
preparing them for use. This will save many steps in going to and from
the basket to get these things. A hole is bored in the trough, to
which is attached a small pipe that allows the water with which the
vegetables or fruits have been washed to run off.
MATERIALS:
18½ ft. of poplar.
¼ lb. No. 5 box nails to nail trough on table.
60 three-penny box nails to nail the zinc on top of table.
16 No. 5 screws, ¾”, to fasten the legs on table.
2 pairs of 2” (butt) hinges to hinge legs on table.
6 3” gate hooks to hook on legs and trough.
6½ lbs. 28-gage zinc to cover the top of table.
1 pail to fit in hole 9” in diameter.
DIMENSIONS:
_Top_: 1 piece ⅞” thick × 24” wide × 44” long.
_Bottom_: 1 piece ⅞” thick × 10” wide × 34” long, to be used as
bottom shelf.
_Crosspieces_: 2 pieces ⅞” thick × 4” wide × 20½” long, to be
hinged on the top of the table.
2 pieces ⅞” thick × 1½” wide × 15½” long, to be used as braces
for bottom shelf.
_Legs_: 4 pieces 1½” thick × 1½” wide × 27½” long.
_Braces_: 2 pieces ¾” thick × 1½” wide × 2½” long, to support top
piece.
_Trough_: 1 piece 6” thick × 5½” wide × 24” long.
1 piece 6” thick × 6” wide × 24” long.
_Hole_: ⅞” thick × 9” wide × 9” long, for opening in center of
table.
[Illustration]
DIRECTIONS:
Measure 4 inches from each end of the top and fasten the two
crosspieces (¾” thick × 1½” wide × 20½” long) putting one on
each end to brace the top of the table. These crosspieces must
also be put at equal distances from the sides of the top. Screw
the legs on these two pieces, using the crosspieces (⅞” × 1½” ×
15½”) as braces for the legs. Use two gate hooks on each end of
table to support the legs when the table is unfolded. The bottom
shelf (⅞” × 10” × 34”) is placed crosswise on the braces and 9”
from the bottom of legs. This shelf is not to be stationary, for
it has to be removed when the table is unfolded. Bore a hole 9”
in diameter in the center of table to hold the bucket. Fasten
the trough, after it has been completed, on the left side of
the table with two gate hooks. Cover the top of the table with
the zinc, using the 60 3-penny nails to tack it on the top.
Sandpaper, stain, and polish the table.
[Illustration]
FLY TRAP
This trap as described below is not only good for the house and the
back porch, where so many flies are attracted by the odor of the foods,
but also excellent for use out of doors. It is inexpensive and can be
easily made at home. Much of the success of the trap depends upon the
bait used. There are many kinds of baits recommended, such as a plate
of vinegar with sugar scattered around it, banana skins, syrups, and
meat. The bait is placed beneath the cone in a saucer, which rests on
the bottom board of the trap. The flies then enter the cone and are
destroyed by smoking before being removed through the hole in the top.
If a poisonous bait is used the smoking is not necessary.
[Illustration]
MATERIALS:
3’ of poplar.
12 5-penny box nails.
1 small box of 3 oz. tacks.
1 ¾” No. 5 screw.
2½ yds. of wire netting, 24” wide.
DIMENSIONS:
_Top_: 1 piece 1” thick × 16” wide × 16” long.
_Bottom_: 1 piece 1” thick × 16” wide × 16” long.
_Cover_: 1 piece ¼” thick × 1½” wide × 2½” long.
_Braces_: 3 pieces ⅞” thick × 1” wide × 24¾” long.
_Cone_: 8” high and 12” in diameter at bottom.
[Illustration]
DIRECTIONS:
Take one piece (1” × 16” × 16”) and find the center, using a
radius of 8” to make a circle for the bottom of the trap. Then
use a radius of 6” to make an opening in the bottom on which
the cone fits. An opening of 1” × 2” is made at some convenient
point in the bottom of trap through which the dead flies are
removed. Take a piece of wood (¼” × 1½” × 2½”) and make a cover
to fit over this opening. Fasten it on the bottom with a screw
so that it may be easily turned. Make the cone of a piece of
wire netting 10” wide. It must fit the inside circle in the
bottom as shown in the illustration. Tack this to the bottom
with 3-oz. tacks. The top of the trap is made just like the
bottom using the same radius. Cut out 3 places in the top and
bottom for the braces (⅞” × 1” × 24¾”) to fit in. These must
extend ¾” below the bottom and nailed in place with 5-penny box
nails. Cover the opening in the top with a piece of wire netting
13” in diameter. The whole frame is then covered with the 24”
wire netting.
GARBAGE BARREL
The problem of the quickest disposal of the kitchen refuse for the
housekeeper is one of great consideration. The garbage barrel, as shown
in the illustration, is a solution for this problem, in that it is put
between rails with a wheel. The garbage may thus be rolled away as many
times a day as necessary, with a minimum amount of effort. A covered
receptacle promotes sanitation around the back premises. The size of
this convenience varies with the material available for making the
device and with the size of the family.
[Illustration]
MATERIALS:
10’ of oak.
8 3½” × ⅜” carriage bolts.
1 barrel
wheel 14” in diameter.
DIMENSIONS:
_Rails_: 2 pieces 1” thick × 6” wide × 28” long, to be used to
hold the barrel in place.
_Handles_: 2 pieces ½” thick × 2¾” wide × 5” long.
DIRECTIONS:
Measure and saw the handles the right dimensions. Taper them at
one end as shown in the illustration. Fasten the rails to the
handles with the eight (3½” × ⅜”) bolts, making the front rail
shorter than the back one. The opening between the rails must
fit the barrel at the bottom hoop. Attach the wheel, 14” in
diameter, to the smaller end of the two handles.
THE SCRUBBING CHARIOT
A clever little device which consists of a comfortable padded frame
which permits the woman to do her scrubbing with more ease and comfort
and saves her from taking many unnecessary steps. To the left it has a
stand for the soap, and on the right may be placed a wire hoop to hold
the bucket of water while scrubbing. This will be found more useful to
the woman who has not access to the more modern conveniences used for
scrubbing.
[Illustration]
MATERIALS:
2½’ poplar.
4 flat trunk rollers for bottom of chariot.
¼ lb. 8-penny nails to be used in making frame.
1 box brass-headed tacks to be used in putting padding
in bottom of chariot.
1 soap holder.
1 yard burlap to make the padding.
DIMENSIONS:
_Bottom_: 1 piece ¾” thick × 10” wide × 20” long.
_Front_: 1 piece ½” thick × 4” wide × 20” long.
_Sides_: 2 pieces ½” thick × 4” wide × 10” long.
DIRECTIONS:
Nail the sides to the bottom board. Fit the front piece to this
and nail to the bottom and sides. Four flat rollers are screwed
on the bottom, and the frame sandpapered, stained, and polished.
A cushion made of the burlap and stuffed with excelsior, a piece
of an old comfort, or cotton, is tacked in the bottom with the
brass-headed tacks. Tack the soap stand on the left side of the
chariot and an iron hoop to the right, if so desired. A soap box
or cheese box may be used to advantage in making this device if
one side is knocked out and the three remaining sides cut down
to the height of 5”.
[Illustration]
SEWING SCREEN
An effort to minimize the “ups and downs” of the busy woman when she
finds a few precious moments to do fancy work or to read. It is an
accessible device, consisting of a light frame, covered with burlap,
with conveniently arranged pockets and other useful features. It is
of a convenient height to be lifted from place to place with a little
effort; or it may be put on casters and rolled around. Its position
near the tired woman’s chair will cause her to feel an eternal warmth
toward the designer, for she will find somewhere on its hooks, shelf,
or in its pockets the very thing needed when with a sigh of relief she
has taken her seat.
[Illustration]
MATERIALS:
10’ of poplar.
22 No. 16 brads, ¾”, for nailing joints.
2½ pairs of 1½” (butt) hinges to be used in joining the
panels, fastening the drop shelf to crosspiece, and
adjusting the bracket.
20 No. 5 flat-headed screws, ⅝”, used for hinges.
2 metal handles to put on top of each side of screen.
4 No. 5 screws, ½”, to put handles on.
2 yds. burlap to cover the screen.
1 box brass-headed tacks to put burlap on screen.
12 brass cup hooks to be used on crosspiece.
1 yd. of creton to make pockets.
Sandpaper and stain.
[Illustration]
DIMENSIONS:
_Stiles_: 4 pieces 1½” × 1½” × 30”, to be used as upright pieces
to screen.
_Crosspieces_: 4 pieces 1½” × 1½” × 12½”, to be used at the top
and bottom of frame.
2 pieces 1½” × 1½” × 12½”, to be used for pegs to hold spools.
1 piece 1½” × 1½” × 12½”, to hinge the shelf.
[Illustration: Sewing Screen]
DIRECTIONS:
On the two upright pieces (1½” × 1½” × 30”) make 4¾” mortises to
fit the tenons made on the crosspieces, making the first mortise
1” from the bottom of the frame and the second mortise 16½” from
the first. The third and fourth mortises in the upright piece
are made 2¼” apart and the third the same distance from the top.
The other upright piece to the panel is treated in the same way.
On two of these crosspieces there are nailed, at equal distances
apart, little pegs to hold the spools. Cup hooks are fastened
on the under side of one crosspiece to hold the bags. Make the
other panel of the screen in the same way, only making mortises
and tenons for three crosspieces instead of four. The first
crosspiece on this panel is put 1” from the bottom; the second,
16½” from the first; and the third piece 4½” from the second.
Hinge the drop door on the top edge of the last crosspiece and
hinge the bracket to support the drop door in the center of
crosspiece. Put the handles on each screen with the 4½” No. 5
screws. Hinge the two panels together and cover the outside of
screen with burlap, using the brass-headed tacks for this purpose.
The frame must be sandpapered, stained, and polished before the
burlap and pockets are put on. The creton pockets are put on the
inside of screen about halfway down the panel.
A HOMEMADE SHOWER BATH
A cheap but convenient arrangement to be used in any home for giving
shower baths where the other fixtures are not to be had. This may be
used to a greater advantage in country homes where there are many
little children. They would find joy in the use of same.
MATERIALS:
1 4-gallon tin bucket
1 medium size zinc tub.
1 nozzle with 6’ rubber tubing.
2 pulleys with 1 staple.
1 piece of piping 2” long.
1 clothes pin.
12’ rope.
1 pint white paint.
1 pint white enamel.
DIRECTIONS:
Cut a hole in the 4-gallon water bucket in the center of the
bottom. On this opening solder the piece of piping, 2” long.
Attach to the end of this piece of pipe the 6’ of rubber tubing
with the nozzle on the other end. The sprinkler from a watering
can may be substituted for the nozzle if not convenient to get
one. Tie a piece of rope to the handle of the bucket and run it
through a pulley which is fastened to the ceiling with a staple.
Have another staple put in the wall below the window sash and
run the rope through it also. This allows the bucket to be
raised or lowered to suit the convenience of the person taking
the shower. A hook is placed below the staple in the window
joist, which holds the bucket in place when not in use. The flow
of the water is adjusted by the use of a clothes pin operated
on the rubber tubing. Use a medium size zinc tub to stand in
while taking the shower. It makes the whole shower bath more
attractive to paint the bucket and tub white and then enamel
them.
[Illustration]
WATERWORKS OUTFIT FOR THE HOME
The following illustration shows a simple but cheap arrangement for a
practical water system to be used in the farm home.
A few minutes pumping each morning by the man of the family will
provide a supply of water for the day’s use, or, where there is no
force pump, the water may be brought in pails until the barrel is
filled every day. While not the most satisfactory plan for putting
water into the home, it is far better than having to carry the water
from a pump or often from a spring which is a long distance from the
house. It is a labor- and time-saving device for the farm woman and
enables her to do more efficient work in every way.
MATERIALS:
1 force pump.
100’ of 1¼” galvanized iron pipe for suction.
Foot valve for suction pipe.
1 piece of rubber hose.
1 tight coupling to bear weight of hose at barrel opening.
1” thick boards to build platform.
1 60-gallon water tight barrel.
½” water pipe to connect barrel with faucet.
1½” faucet.
1 sink (18” × 30”).
50’ of 1¼” lead pipe to be used for S-trap.
50 ft. 4” drain pipe.
DIRECTIONS:
_Pump._: Bore a hole about 2” below the lid of the barrel. This
must be large enough to permit the piece of coupling to fit in
it tightly. It is not necessary to use the coupling but it will
give a better support to the hose. Fasten one end of the hose to
the coupling and the other end to the pump. On the opposite side
bore a hole with a ¾” auger and attach the ½” piece of water
pipe to it.
_Shelf_: Raise the barrel to the platform, which is made of 1”
boards, and well braced underneath. This platform is fastened
to the house just outside of the kitchen. It must be put higher
than the kitchen sink in order to obtain pressure enough to give
a steady flow of water. A tight-fitting lid is placed on top of
the barrel to keep out the trash and the insects. Fasten the
faucet to the ½” pipe on the barrel which extends through an
opening made in the wall.
_Sink_: Place the sink, supported by brackets, on the inside of
the kitchen wall and at a convenient height from the floor for
the woman to comfortably use.
_Drainage_: Fit the S-trap to the 4” drain pipe to carry off the
water from the sink.
[Illustration]
CHAPTER V
=POULTRY DEVICES=
POULTRY HOUSE
A portable house placed on runners is shown in the following cut. It
can be easily moved by four men carrying it, or be drawn by hitching
a horse to the ends of the runners. A house of this type has many
advantages over the stationary house because it can be moved into the
field after the grain is cut, into the orchard, and into the different
fields where the chickens can get plenty of fresh green food.
MATERIALS:
Use Size No. of Length Board
pieces measure
Sills (runners) 4” × 6” 2 12’ 48’
Joists 2” × 4” 3 14’ 28’
Studs and braces 2” × 3” 13 12’ 78’
Rafters 2” × 4” 3 16’ 32’
----
Total 186’
⅞” Matched flooring (floor and sides) 340’
⅞” Sheathing, surfaced one side 100’
Roofing paper, 1 roll.
Windows, hardware, etc.
DIRECTIONS:
A good location is the first consideration in the building of a
poultry house. Select a well drained spot, facing the southeast
and large enough to make comfortable quarters for the chickens.
The house is built of any kind of durable and well-seasoned
lumber. The kind of material used in making the floor will
depend largely on the soil and the money to be spent in the
construction of the house. Board floors are often used but they
are more susceptible to rats. Cement floors are more easily
cleaned and more sanitary, and not so expensive in a locality
where plenty of gravel is available. A board floor must be
raised several inches from the ground as a protection from rats
and to allow for runners to be placed underneath the house.
[Illustration: A portable poultry house, showing the exterior and
interior]
Roosts are placed on the same level with each other next to the
end or back walls and from 6” to 10” above the dropping boards,
which are 2½” from the floor. Roosts may be stationary as in the
cut, or they may be fastened by hinges to the walls and raised
to clean the dropping board.
Roost spacing will depend upon the size of the fowls, but a 10”
space to each fowl is usually sufficient. They must be put 15”
apart.
Nests made 14” square are built under the dropping boards around
the walls of the house as shown in cut. A 4” piece of wood is
placed on the side, which drops as a door in front of the nests.
Windows as shown in the cut are more expensive and not as good
as a front made of wood extending about 2’ from the bottom. Wire
screening, admitting better ventilation and more sunlight, is
tacked over the rest of the opening in the front. A curtain may
be made of unbleached muslin and fastened on a pole at the top
of the open front, which may be lowered as a protection in bad
weather.
Make the roof of some water tight material and cover the walls
on the inside to protect the fowls from draughts.
_Nests._--Comfortable and convenient quarters must be furnished the
sitting hen. The location of the nest must be in a quiet, dark place
to keep the hen from becoming restless. A box fifteen inches square
and twelve inches high, with a narrow strip four to five inches wide
at the bottom of the open front of the box, makes a comfortable nest.
Barrels or half-barrels or nests made of a piece of sod will also be
comfortable quarters for the sitting hen. The nests must be well lined
with hay, straw, or excelsior. Both the nests and the hen must be
thoroughly dusted with insect powder before the sitting time comes.
_Hatching and Rearing._--There are two methods used in the hatching
and rearing of chickens--the natural, when the chicks are hatched
and reared by a hen, and the artificial, when they are hatched in
incubators and brooded in houses indoors or out-of-doors. The natural
method will be found to be more satisfactory when dealing with a small
number of chickens. A small number of hens, if managed with system and
care, will produce a large number of chickens at a very small cost.
Care must be taken in the selection of the eggs to be used for hatching
purposes. Select well-formed eggs which are regular in shape and size
and which are neither too large nor too small. They should come from
healthy hens of one breed and should be smooth and of one color. Eggs
must be kept in a dry, cool place and at a temperature of from fifty
to sixty degrees Fahrenheit. The fertility of an egg weakens with age;
so they must be kept only a few days before they are to be set. The
number of eggs to be put under each hen will vary with the season, the
size of the hen, and the size of the eggs; but it is usually safe to
put about thirteen eggs under a hen of average size.
_Egg Tester._--Test the eggs in a dark room on the seventh and
fourteenth days for the removal of infertile eggs. This may be done by
a very simple home-made tester made of a pasteboard or wooden box, with
a hole the size of an egg bored in the front, and an opening in the
top through which the smoke is to pass. If a wooden box with a bottom
is used, an opening must be made in front, with a door so as to put
the lamp in. A box without a bottom may be used and simply set right
over the lamp. Either a lamp, candle, or lantern may be used on the
inside of the box. Holding the egg in front of the box and letting the
light shine through it will show the condition of the egg. An infertile
egg will be clear, while a fertile egg has a spider-like center with
threads leading out from it. All infertile eggs must be removed.
[Illustration]
Poultry is classified as the egg breeds, the meat breeds, the
general-purpose breeds, and the ornamental breeds.
The egg breeds are small fowls which mature quickly. They are very
active, but not good chickens to be used for setting purposes. They
are good layers, and they lay a great many white-shelled eggs, for
which there is a great demand on some markets. The age of maturity
for this breed is from four and one-half to five months. The Leghorns
and the Minorcas are the principal representatives of this breed. The
single-combed white Leghorn has been the most popular.
The meat breeds are large fowls with long necks and heavy coats of
feathers; and they lay a comparatively small number of brown-shelled
eggs. They are slow in movement, with little desire to forage. They
make fine mothers, and for this reason they make good fowls to be used
for setting. The Brahmas, Cochins, and Langshanks are the principal
fowls of this breed.
The general-purpose breeds occupy a medium place between the egg and
meat breeds as to size, egg production, and meat production. For these
characteristics they are especially recommended to the farmer who
wishes both egg and meat fowls. They lay a number of brown-shelled
eggs and they make splendid mothers. The Plymouth Rocks, Wyandottes,
Orphingtons, and Rhode Island Reds are the best varieties of this breed.
The ornamental breeds are ornamental both in character and purpose, and
for this reason they are not practical for use on the farm.
_Feeding._--The farmer has often become discouraged by the elaborate
rations which are recommended by poultrymen to be used in feeding the
chickens. While some of the by-products of industries, such as Linseed
Meal and Meat Meal are necessary, most of the feed used in poultry
raising may be raised on the farm. It is well to be familiar with the
different values of foods fed to the chickens, for they like a change
in their rations, and it is necessary that they have it. If the food
contains too much fat, the hens will become too fat, which will lessen
their usefulness as egg producers; while if the food contains too
much protein, some symptoms of indigestion will result. It is hard
to determine the right amount of fat and protein to be fed to the
chickens, for this varies to suit conditions and the purpose for which
it is fed.
Broad Ration Food Available
Protein Fat
2 parts wheat bran .244 .906
1 part wheat middlings .128 .607
1 part cornmeal .079 .764
⅒ part meat meal .066 .033
----- -----
.517 2.310
Ratio 1: 4.4
Narrow Ration Food Available
Protein Fat
2 parts wheat bran .244 .906
1 part wheat mids .128 .607
⅒ part linseed meal .029 .048
⅒ part meat meal .066 .033
----- -----
.467 1.594
Ratio 1: 3.4
Young chicks should be fed a dry or wet feed forty-eight hours after
they are hatched. Nature has already provided them with yolk of egg,
which must be digested before they are given more food. Their first
feed must be fine grit or a drink of sour milk. In two hours after
the first feeding they may be given dry oat flakes with an egg which
has been boiled for an hour, or a Johnny cake made of ten parts of
cornmeal, two parts of wheat middlings, two parts of wheat bran, mixed
with skimmed milk and baked. Change this diet after a week to a dry
ration--for example, two parts of cracked wheat, two parts of oat
flakes, four parts of cracked corn, one part of rice, and one part of
millet. Plenty of green food and sour milk should be fed to them. Feed
them often, but in small proportions. Let them take plenty of exercise.
It is important to keep the hen up and allow the chicks to run out
until they are weaned.
DRY MASH HOPPER NO. 1
There are many kinds of dry mash hoppers on the market but it is
difficult to find one that is not wasteful. This hopper which is made
of poplar is easily made and it has been found to be very successful.
It may be built of the desired length and made to hold the required
amount of dry mash. The most important detail in the building of
this hopper is the slope of the bottom which must be at an angle of
forty-five degrees with the wall of the henhouse. It must be built
well off the floor with a roost placed for the hens to stand on while
they are feeding. This will keep the litter out of the hopper. The
wire netting must be of one-quarter inch square mesh which is fastened
to the hopper and stretched to the bottom of the trough at its lowest
point.
MATERIALS:
12½’ poplar.
1 lb. 6-penny nails.
16 ¾” No. 8 screws.
32 No. 10 screws.
2 pairs of 1½” (butt) hinges.
1 piece of ¼” mesh wire.
2” × 2” gate hooks.
DIMENSIONS:
_Body_: 2 pieces 1” thick × 5” wide × 26” long, to be used as the
ends of the hopper.
2 pieces 1” thick × 9” wide × 19” long, to be used as the top
and the bottom of the hopper.
1 piece 1” thick × 19” wide × 26” long, to be used as back of
the hopper.
1 piece 1” thick × 19” wide × 17” long, to be used as front of
hopper.
_Trough_: 1 piece 1” thick × 4” wide × 19” long, to be used as
front of trough.
1 piece 1” thick × 5” wide × 19” long, to be used as the lid in
the front of trough.
2 pieces 1” thick × 4” wide × 9” long, to be used as sides of
trough.
_Roost_: 1 piece 1” thick × 2” wide × 21” long, to be used as
front of the roost.
2 pieces 1” thick × 2” wide × 15” long, to be used as sides of
roost.
DIRECTIONS:
Take the two end pieces (1” × 5” × 26”) and cut the tops at
an angle of 60 degrees and the bottom of these ends at an
angle of 45 degrees. Nail the bottom piece (1” × 9” × 19”)
to these end pieces and then nail on the back (1” × 9” ×
26”).
[Illustration]
The front piece (1” × 19” × 17”) is then nailed on the
hopper.
The two end pieces (1” × 4” × 9”) to be used on the trough
are cut at an angle of forty-five degrees at one end and
nailed on each side of the bottom of the hopper as shown
in the illustration. Then the front of the trough (1” × 4”
× 19”) is nailed to the sides. Tack the wire mesh over the
opening in the trough and hinge the front piece (1” × 5” ×
19”) on the front of the trough with one pair of 1½” (butt)
hinges. The other pair of hinges is used to fasten the top
(1” × 9” × 19”) on the hopper.
Make the roost by nailing the two sides (1” × 2” × 15”) to
the front (1” × 2” × 21”). Fasten this frame on the sides
of the hopper with two two-inch gate hooks as shown in
illustration.
The hopper when completed is fastened to the sides of the
wall of the henhouse with thirty-two number ten screws at a
convenient height to the chickens.
[Illustration]
DRY MASH HOPPER NO. 2
This model is constructed very much like the hopper already described
with the exception of the four compartments which provide for a
balanced ration for the chickens. It is not nailed to the wall but
rests on the floor.
MATERIALS:
12½’ poplar.
1 lb. 6-penny nails.
8 ¾” No. 8 screws.
1 pair of 1½” steel butts.
1 oz. No. 16 wire staples.
12” of No. 4 mesh wire 36” wide.
DIMENSIONS:
_Body_: 2 pieces 1” thick × 6” wide × 2’ 8” long to be used as
sides of the hopper.
1 piece 1” thick × 6” wide × 16” long to be used as bottom of
the hopper.
1 piece 1” thick × 1’ 8” wide × 2’ 8” long to be used as back
of hopper.
2 pieces 1” thick × 2” wide × 1’ 8” long and 1” thick × 6” wide
× 1’ 8” long to be used as the lid of the hopper.
1 piece 1” thick × 1’ 8” wide × 2’ long to be used as front of
hopper.
3 pieces 1” thick × 6” wide × 2’ 6” long to be used as partitions
for making the equal compartments in the hopper.
_Trough_: 2 pieces 1” thick × 4” wide × 10” long to be used as ends
of trough.
2 pieces 1” thick × 4” wide × 1’ 8” long to be used as front and
back of trough.
3 pieces 1” thick × 4” wide × 4” long to be used as partitions
in the trough, making four equal compartments.
DIRECTIONS:
Nail the two end pieces (1” × 6” × 2’ 8”) to the bottom piece
(1” × 6” × 16”). Then nail the back piece (1” × 1’ 8” × 2’ 8”)
and the front piece (1” × 1’ 8” × 2’ 4”) to the ends of the
hopper. Nail the partitions (1” × 6” × 2’ 6”) to the back and
front of the hopper making four equal compartments.
The trough is made by nailing the two end pieces (1” × 4” × 10”)
to the side of the hopper. Nail the front (1” × 4” × 1’ 8”)
and the back (1” × 4” × 1’ 8”) to the ends of the trough. The
partitions (1” × 4” × 10”) are nailed to the front and back of
the trough, making four equal compartments. Cover the opening in
the front of the trough with 12” of No. 4 mesh wire 36” wide.
Hinge the two top pieces (1” × 2” × 1’8” and 1” × 6” × 1’8”)
together with one pair of 1½” steel (butt) hinges. Then nail
this top piece to the back of the hopper with the narrow strip
even with the edge of the top end of the back.
[Illustration]
[Illustration]
RACK FOR OAT-SPROUTING TRAYS
The importance of giving poultry green feed throughout the year cannot
be over-emphasized. This sprouting tray is very convenient in order
that this food be furnished the chickens. It is a simple construction,
made of yellow pine, and a device that can be made by any farmer at
a minimum cost. It is advisable to lay off all the material before
beginning to build the rack, to avoid confusion in the measurements.
MATERIALS:
23½ feet of yellow pine.
28 lbs. of 28-gage galvanized metal to make sprouting trays.
1 lb. 8-penny nails for building rack.
DIMENSIONS:
_Top_: 2 pieces 1” thick × 2” wide × 2’6” long.
_Bottom_: 2 pieces 1” thick × 2” wide × 2’6” long.
_Corners_: 4 pieces 2” thick × 4” wide × 6” long for upright
corners.
_Brace_: 1 piece 1” thick × 2” wide × 6’6” long.
_Cleats_: 14 pieces 1” thick × 2” wide × 2’6” long, to hold trays
of same proportions.
DIRECTIONS:
Take 2 upright pieces (2” × 4” × 6”) and nail to bottom (1” × 2”
× 2’6”). Measure a distance of two inches from the top and nail
on first cleat (1” × 2” × 2’6”). Cleats are nailed on the back
of the frame even with the ends of the upright pieces (2” × 4” ×
6”). Nail brace (1” × 2” × 6’6”) diagonally from one corner to
the other. Nail the first cleat 9 inches from the bottom edge of
the upright piece. All the other cleats must be nailed 8 inches
apart. In each of the sprouting trays a hole ¼ of an inch in
diameter is bored to allow the water to drain out from the tray.
[Illustration]
_Dust Boxes._--Dust boxes are necessary during the winter months to
keep the chickens from wallowing in the dirt, as this is the method
used by them to cleanse themselves. A box four feet by four feet
will be large enough to accommodate fifty chickens. Fine, light, dry
dust should be kept in these boxes, and they should be placed in the
sunlight and where they may be easily reached by the chickens.
_Drinking Vessel._--Should be large enough to hold sufficient water to
last twenty-four hours. They must be elevated in some way to keep the
dirt from getting into them. A practical drinking vessel is made of a
Mason glass jar. Make perforations in the top of the jar with a nail
and tack two strips of wood across the top crosswise to raise the jar
from the saucer or plate. This allows the water to flow freely from
the jar as fast as the chickens can drink it from the saucer, and the
covered jar keeps the drinking water clean.
[Illustration]
_Brooder._--A simple and convenient chicken brooder may be made of
an old wooden tub which is turned upside down on a platform with
the bottom of the tub knocked out, and a covering placed over the
top. This, with windows cut in the sides of the tub, gives a better
ventilation for the chickens. A door through which the chickens enter
is cut in the front. Outside of the brooder and on one end of the
platform is a simple watering device supplying the chickens with fresh
water.
[Illustration]
CHAPTER VI
=DAIRY DEVICES=
SHOWING USE OF BUTTER-MAKING EQUIPMENT
The economic value of farm butter made from the product of a few
cows is of much more importance than is commonly supposed. For this
reason the fundamental principles underlying the making of good butter
should be practised as much by the farm woman, making butter in small
quantities for the market or the consumption in the home, as by the
operator of a large creamery establishment. The quality of butter made
on the average farm shows that cleanliness and the proper attention to
the simplest details in the making of good butter have been neglected.
_Quality._--The method used in the handling of milk or cream and in
making butter determines its quality. The sanitation of the utensils
in which cream or milk is handled and the conditions surrounding it
during ripening are of the utmost importance. A common practice among
some farm women is to put the milk in shallow, uncovered pans which are
exposed to dust, flies, and the odors which frequent the pantry and
kitchen. Such pans are allowed to stand until the milk clabbers and a
thick leathery sheet of cream is formed on the top. Good butter cannot
be made from milk or cream handled in this manner. A deep, narrow
vessel known as a shot-gun can is recommended for use in ripening cream
or milk because it is easily handled, washed and can be covered. These
can be bought at hardware stores or mail order houses.
_Utensils._--Convenient equipment for making butter is essential and
very inexpensive. It is customary on many farms to churn the cream in
an earthen jar with a wooden dasher and stick. Earthenware vessels
commonly used are porous and often contain blisters or air bubbles, all
of which will absorb milk. The milk sours in these places and gives the
vessels a characteristic bad odor. These churns are hard to clean and
heavy to handle and should never be used. A wooden barrel churn is one
of the best types to use because it is easily operated, cleaned, and
handled. Churns which contain agitators and gearing of different kinds
should not be used.
A dairy thermometer, which can be bought at any local hardware or drug
store at a small cost, is necessary to determine the temperature of the
cream.
When there are at least four cows milked, a small cream separator will
be a good investment. Where a separator cannot be had, hand skimming is
advisable if the cream is properly handled.
_Ripening of Cream._--The ripening of milk or cream is the natural
souring which takes place under proper conditions and which gives
butter its characteristic flavor. The quality of butter depends, to a
large extent, upon proper ripening. Where hand skimming is practised,
set separate milkings in cool, well-ventilated places and allow to
stand from twelve to eighteen hours for the cream to rise. Skim the
cream off with a cup or large spoon, put it into a can which is
kept in a cool place at a temperature of 50 degrees Fahrenheit or
below. Skimmings from the different milkings are cooled to the same
temperature before being added to this stock can. The contents of this
can must be stirred each time after adding the cream. When sufficient
cream for a churning has been secured in this way the contents of the
stock can are warmed to a temperature of 58 to 60 degrees Fahrenheit
and in winter 62 degrees Fahrenheit, then allowed to stand in a clean,
well-ventilated place for twelve or eighteen hours to ripen. This
warming is done by setting the can in a vessel of hot water. Frequent
stirring is necessary during the ripening period. Cream properly
ripened has a velvety and glossy appearance, with a mild but pleasant
sour taste. When hand skimming is not practised the churning will have
to be done more frequently to prevent the milk from becoming too sour
and giving the butter a bad flavor.
_Coloring the Butter._--The natural color of butter when the cows can
get plenty of nature’s food is a soft, straw yellow. During the winter,
if it is necessary to use dry feed alone, the butter will lack color
which can be supplied by the addition of a harmless coloring matter.
The amount of coloring matter necessary to use varies with the season
but usually 8 to 12 drops of harmless vegetable coloring to every pound
of butter will be sufficient in the winter time. This coloring matter
may be bought at most drug stores.
_Churning._--When the cream is ready for churning, rinse the churn
with scalding water to cleanse it thoroughly and to swell the pores in
the wood. Following this, cool the churn with cold water to prevent
the raising of the temperature of the cream when put into the churn.
The cream should be poured through a strainer into the churn to remove
lumps or hard white specks of cream which may have dried to the sides
of the can. Gas will form in the churn during the first few minutes
of churning which must be let out by removing the cork at the bottom
of the churn. It may be necessary to repeat this operation several
times. After the churn has been in operation about 20 minutes, the
cream becomes thick and shortly after, very small, mealy granules
begin to form. At this point the cream begins to break away from the
glass in the top of the churn lid. When this stage is reached, after
every four or five revolutions the lid should be removed and the size
of the granules observed. When these have reached the size of large
wheat grains, the churning operation has been completed. At this point
the glass in the top appears clear which indicates that the granules
slide off instead of sticking to the top. It usually takes at least 25
minutes to churn good butter. If it takes longer, the temperature of
the next cream churned should be raised a few degrees.
_Washing the Butter._--When churning is completed draw the buttermilk
off through a strainer to catch small particles of butter. The butter
is washed to remove the buttermilk, to improve the flavor, and to
keep better. Buttermilk is washed out of the butter and not worked
out. The temperature of the wash water should be the same as that of
the buttermilk and is determined by the use of a thermometer. This
temperature depends upon the condition of the butter; if the butter is
too soft the water must be colder, and _vice versa_. In washing butter,
water is added and the churn given two or three revolutions so as to
turn the butter; after which the water is drawn off and the process
repeated several times until the water drawn off is clear.
_Salting the Butter._--The butterworker, paddles, and mold or printer
are scalded and cooled in the same way as the churn and for the same
reasons. The churn is then drawn near the worker and the butter
granules removed with paddle or ladle and placed on worker. The hands
must never touch butter for sanitary reasons and because they will give
the butter a greasy appearance. As soon as the butter is placed on the
worker, one ounce of fine, clean salt to a pound of butter is sprinkled
uniformly over the butter.
_Working the Butter._--Butter should then be worked well to distribute
the salt through it and to expel the excess water. Butter is salted to
improve the flavor, to serve the market purposes and to some degree to
act as a preservative. In working the butter, the pile of granules is
pressed flat with the lever, and the flattened mass of butter turned
over about 12 or 14 times until the edges of butter, when broken, have
a granular appearance similar to a broken half-baked potato. Too much
working destroys the grain and the edges when broken apart will have a
slightly stringy appearance, while too little working gives a streaked
or mottled butter.
_Printing and Wrapping the Butter._--The printer is removed from the
water as soon as the working has been completed and with both hands
it is pressed on the mass of butter until it is packed full. That
remaining over the edge is then cut off with a paddle and the print
pushed out on a sheet of parchment paper and neatly wrapped. The
printing and wrapping of butter cannot be emphasized too strongly, for
a good appearance is fundamental to obtaining good markets for the
butter. It is very much easier to get a good market for butter packed
neatly in parchment paper than it is for that wrapped in a cloth as is
the case in so many country homes. It is very important that a good
grade of parchment paper should be used for wrapping butter and this
can be bought from firms handling dairy supplies or it may be ordered
by mail. The brick-shaped mold is used because prints can be handled
with convenience and such prints are a standard on the market. A
mold of this kind can be purchased from local hardware stores or mail
order houses for from $1.50 to $5.00. The placing of the wrapped print
in a pasteboard box or carton not only protects the butter from the
finger prints but also from dust and dirt. These cartons may be bought
from any firm handling dairy supplies. Butter put up in this manner
is convenient to handle, attractive in appearance, and is also an
advertisement.
_Marketing the Butter._--The appearance of the package determines to
a large extent the selling price of butter and every effort should
be made to make it as neat, attractive, and convenient to handle as
possible. The ultimate end in the making of farm butter is to supply a
delicate food for the family and to obtain a profit from the surplus.
To do this, it is necessary to create a demand by giving satisfaction
to your customers. This can be done by putting up butter superior in
quality and attractive in appearance.
BUTTER WORKER
A very useful appliance, and easily operated, making the butter into a
close-grained mass without injuring the texture of it. It is made of
poplar, triangular in shape, with a corrugated roller. This roller fits
in a hole made in a piece of metal which is put across the smaller end
of the worker. This worker may be operated by putting it on the kitchen
table, or it may be placed on adjustable legs.
[Illustration]
MATERIALS:
13’ maple for bottom, sides, and battens.
3’ 1⅜” × 2” × 5” for roller.
10 No. 14 screws, 3” to fasten the sides on bottom.
8 No. 14 screws, 3” to fasten battens on bottom.
1 piece 28-gauge zinc 4¾” wide × 16” long, for front piece.
8 four-penny box nails to fasten zinc across the front.
1 pan 2” deep × 12” wide × 14” long, to place under worker in
small end to catch drippings from butter.
Wood glue to fasten handle on roller.
DIMENSIONS:
_Bottom_: 1 piece 1¼” thick × 30” wide in front, 4” wide in back
× 26” long.
_Sides_: 2 pieces 1¼” thick × 6” wide, × 30” long.
_Battens_: 1 piece 1¼” thick × 4” wide × 30” long.
1 piece ¼” thick × 2” wide × 2” long.
_Roller_: 1 piece 4” thick × 4” wide × 36” long.
_Handle_: 1 piece 5” long.
[Illustration: Taking temperature of cream]
[Illustration: Straining the cream into the churn]
[Illustration: Churning operation complete]
[Illustration: Working the butter]
[Illustration: Moulding and packing the butter]
[Illustration: Cleaning up]
DIRECTIONS:
Taper the bottom piece at one end, using a radius of 31”. Screw
the battens (1¼” × 4” × 30”) (1¼” × 2” × 2”) on the bottom,
making the holes large enough to fit the heads of the screws.
Taper the two sides and nail them to the bottom. The roller is
made 36” long and 2” in diameter, measuring ¼” from the end to
round the corners. Bore a hole in the end and put the handle on
it. Put a small metal pin in the end of roller to hold handle in
place. Tack the piece of zinc across narrow end of the worker,
making a hole in the centre to fit end of roller. Sandpaper when
completed.
[Illustration: Butter Worker.]
MILKING STOOL
A convenient device used in milking, which not only provides a seat for
the one who is milking, but a platform with a hoop to hold the bucket.
The bench is light in weight which makes it easy to handle. When not in
use it may be hung on the wall.
MATERIALS:
2½’ yellow pine.
1 piece of metal, 1” wide × 15” long, to make hoop to hold bucket.
¼ lb. 6-penny nails.
Sandpaper and paint.
[Illustration]
DIMENSIONS:
_Top_: 1 piece ¾” thick × 10” wide × 14” long.
_Brackets_: 4 pieces ¾” thick × 3” wide × 3” long to support top
shelf.
2 pieces ¾” thick × 2” wide × 3” long to support shelf which
holds bucket.
_Shelf_: 1 piece ¾” thick × 3½” wide × 10” long to hold bucket.
_Ends_: 2 pieces ¾” thick × 10” wide × 11⅛” long.
[Illustration]
DIRECTIONS:
Make the top of the stool, using the piece (¾” × 10” × 14”),
rounding both ends to a radius of 5”. Make the front and back
supports as shown in illustrations 4 and 5. Make the bucket
shelf (¾” × 3½” × 10”) next, fastening the two pieces (¾” × 2”
× 3”) to the shelf as supports and then nailing the whole to
end of stool. Sandpaper the stool and then paint the whole any
desired color, preferably white.
CHEESE-MAKING EQUIPMENT
Devices used in the process of making cottage, Neufchatel, and cream
cheese are given, accompanied by directions for the use of each of
these devices in the making of these cheeses.
_Construction of Drainer._--The rack shown in the figure is 13 inches
wide, 13 inches long, and 10 inches deep. The corner posts extend 1½
inches above and below the strips at the top and bottom with the tops
rounded as shown in the illustration. The bottom slats fit loosely into
notches, hence they may be removed when the draining rack is washed.
The materials required are four corner posts 1½ × 1½ inches; 15 strips
1 × ⅜ × 13 inches and 2 strips 1 × ⅜ × 13 inches notched to receive the
bottom slats. Pine or poplar may be used for the construction of this
device.
[Illustration]
_Construction of Press._--3 or 4 inch poplar boards 18 × 18 inches are
used for this press. Cleats are placed on the back of these boards to
keep them from warping. The lower board of this press has a circular
groove which has an outlet in one side to allow the whey to drain off.
[Illustration: Drawing the curd]
[Illustration: Pressing the curd]
[Illustration: Moulding the cheese]
[Illustration: Necessary equipment used in cheese-making]
_Cottage Cheese._--Cottage cheese has been produced from time
immemorial upon the farm. Ordinarily, it is made from milk that has
been allowed to stand until it thickens by natural souring. It is then
skimmed. After skimming, the rather firm mass of loppered milk is
stirred with a large wooden spoon.
Simultaneously with the gentle breaking of the coagulum the temperature
of the mixture of whey and curd is gradually raised to about 95 degrees
Fahrenheit and maintained at that temperature for five minutes. This
mixture should be stirred occasionally but not vigorously. Too much
stirring will cause the mass to drain slowly. After this heating
process the mixture of whey and curd is poured into the draining cloth;
usually muslin or cotton sheeting is stretched over the draining rack,
which is especially constructed for this purpose. Such a rack as shown
in the illustration can be made very easily and at a small cost. Thirty
pounds of milk per rack may be easily handled. Perhaps, in handling
the milk in this quantity, it would be advisable to make the rack
somewhat longer than the one illustrated. A rack rectangular in shape,
13 inches wide, 36 inches long and 10 inches deep is sufficient. The
draining mixture is left undisturbed for half an hour and then the curd
is worked toward the center of the cloth by means of a spoon or ladle.
The last of the whey is removed by raising and lowering repeatedly the
ends of the draining cloth. After draining the curd in this manner
the corner of the cloth is folded over to form a sack and the curd is
placed between the heavy boards or press. If more pressure is needed
weights may be placed on the top board. When the curd has acquired the
consistency desired it is salted to suit the taste, and usually a small
amount of cream is added. The use of the latter, however, is entirely
optional.
The expulsion of the whey by heating hardens the particles of curd,
giving a grainy texture to the mass.
_Neufchatel Cheese._--Fresh clean milk is required to make a high-grade
Neufchatel cheese. In no case should the milk be over twelve hours old.
A slow development of a clean acid flavor is demanded. The addition of
a commercial lactic starter in small amounts aids in obtaining curd
free from objectionable ferments. Too much starter will produce acid
too rapidly and give a rough mealy curd. A very satisfactory product
may be secured, if the milk is reasonably clean, without using any
starter.
_Starter._--The starter is merely soured milk. In making a home-made
starter place a clean milk bottle and tumbler in a pan of cold water
and bring same to boiling; remove the bottle, allow it to cool and then
fill it with the freshest, cleanest milk available. The bottle should
now be covered with a sterilized glass tumbler in order to prevent the
entrance of dirt. Allow the milk to sour at a temperature of about 75°
F. (room temperature).
Two cubic centimeters of active starter for each thirty-pound can of
milk will give good results. After adding the starter the milk is
vigorously stirred and warmed to a temperature of 80° F. Rennet is now
added at the rate of 30 drops per 100 pounds of milk. Upon a small
scale junket tablets may be used for curdling purposes. The mixture,
after being thoroughly stirred, is left at rest over night at room
temperature, or preferably a little higher. The firm curd is now poured
upon the draining rack as with the cottage cheese and allowed to drain
for about two hours. Toward the end of the draining period the curd is
worked toward the center of the cloth by means of a ladle. The cloths
containing the curd are now tied together bag fashion and pressed. The
hand-made contrivance illustrated may be used, or merely allow weights
to rest on bags of curd over night. The more whey that is removed the
better will be the flavor and keeping qualities of the cheese. The curd
should drain out and not dry out. Mix in the salt to suit the taste by
using a butter worker or a pail and potato masher. Ordinarily about one
ounce of salt to four pounds of curd is sufficient. The cheese is now
ready to be run through the food chopper and molded. Sometimes it is
packed tightly into screw top jars or jelly glasses with tight covers,
but usually the cheese is molded into shape and wrapped in parchment
paper, surrounded by tin foil to exclude the air. Such molds may be
formed by hand closely enough to exclude the air. Butter printers are
often used. If the work is done upon a small scale some kind of a hand
formed package is probably most economical.
_Cream Cheese._--Cream cheese is made in practically the same way as
Neufchatel cheese except that the former is made out of cream testing
from 6 to 8 per cent. fat.
More detailed information on the subject of making cheese can be
obtained from the bulletins and books suggested for reference reading
in the list given in the back of this book.
=APPENDIX=
FUNDAMENTALS IN WOODWORKING
NOTE.--Some of the terms used in the text are explained in this chapter.
_Tenon._--A tenon is a piece of wood shaped like a tongue by dividing
the end into three rectangular parts, cutting the sides away and
leaving the middle which is shaped to form a tongue.
_Mortise._--A mortise is a hollow cut in to receive a corresponding
piece of wood. It is made by measuring the required distances on a
piece of wood and boring holes. Take out these portions of wood with
a chisel until the mortise is of the required size. Mortise and tenon
joints put together in one direction, as those made in the back of
a chair, are much easier made than those which are joined in two
directions, as in the framework of a stool.
_Mitred Joint._--There are many modifications of this joint but the one
most used is the one made at an angle of 45 degrees. Mitred joints are
easily made but they have a tendency to shrink, leaving an opening on
the inside of the joint.
_Cleat._--A piece of wood nailed down to secure something from
slipping. The size of a cleat will be determined by the weight which it
is to hold.
_Bevel._--A bevel is a finished edge to a piece of wood. The kind of
problem must determine the kind of beveled edge to be made. The blade
of the square must be set at the correct angle in making a bevel edge.
The most popular bevel is made by setting the bevel square at an angle
of 45 degrees.
_Bracket or Brace._--A supporting piece for a shelf or any other place
which needs strengthening.
_Panel._--Any area out of level. It may be sunk below or raised above
the general face of the surrounding work. They are set in grooves made
the proper depth with a plane. Every piece of wood used in panelling
must be straight with the face surface of the wood and straight and
square with the front edge to make a flat and square panel.
_Groove._--A groove is a furrow or a long hollow. The depth of the
furrow depends on the rail it is to hold.
_Taper._--A taper is a graduated point. All parts of the surface must
have the same amount of taper to make it equally tight at all points
when driven into place. Draw lines on the end of the wood and across
the center at equal distances from the corners and with the surface
straight on both sides. Care must be taken not to split the corners
while making a taper.
_Plugs._--Plugs are pieces of tapered wood used as a stopper, such as
in the illustration of Jelly Strainer No. 2. When plugs are to be used,
the holes must be made in the wood before the pieces are put together.
“_Penny._”--This term is a corruption of “pound” and used in speaking
of different kinds of nails. For example, eight-penny nails means that
one thousand of them weigh eight pounds.
_Radius Bar._--A bar pivoted at one end, about which it swings, and
having its other end attached to a piece which it causes to move in a
circular arc as in the corrugated roller made to work the butter.
_Finishing._--There are two things to be considered in finishing
woodwork; the preservation of the wood, and the artistic finish. Three
steps are necessary in putting on the finishing touches. First, the
surfaces made smooth by the use of sandpaper; the second, staining or
varnishing, and the third, polishing.
_Sandpaper._--Sandpaper is not expected to do the work of edged tools.
Tool work must be completed before using sandpaper, or particles of
dust will get into the pores of the wood which will dull the tools
while working with them. Never sandpaper across the grain of the wood.
While dressing flat surfaces, use a piece of sandpaper put over a block
of wood.
_Stains._--Water, oil, and alcoholic stains are used for staining
woodwork. All have their advantages and disadvantages, but for general
purposes the alcoholic stains are highly recommended, Johnson’s wood
dye being one of the best. A good water stain is made by boiling an
extract of logwood, the size of a walnut, with four ounces of water.
This is applied to the wood while hot, using a brush or sponge with
which to apply it. Repeat the application until the desired color is
obtained. Varnish must be used only when a hard, transparent finish is
desired.
_Polish or Wax._--Satisfactory results cannot be obtained unless the
surface is smooth and well prepared by the use of sandpaper and stain.
A cheap recipe for making wax is given as follows:
1 lb. beeswax.
½ pt. alcohol.
1 pt. turpentine.
Break up the beeswax and melt it into the consistency of thick cream
in a bowl placed in a saucepan of boiling water. Remove bowl from the
fire, gradually beating into the wax the turpentine and alcohol. Store
it away in covered jars and warm slightly when it is to be used. Spread
a thin layer on a soft woollen cloth and apply it to the surface.
SUGGESTED LIST OF TOOLS
1 Stanley “Bed Rock” smooth-plane, No. 603 $1.60
1 Disston’s Crosscut-saw, No. 9, 22”--10 points 1.15
1 Disston’s Back-saw, No. 4, 10” .95
1 Buck Bros. firmer chisel, 1” .35
1 Buck Bros. firmer chisel, ¼” .20
1 Hammond’s Adze-eye hammer, No. 3, 7 oz. .45
1 Hardened blade try-square, No. 5½, 6” .25
1 Beech Marking-gage, No. 64½, 8” .20
1 Sloyd Knife, No. 7, 2½” blade .30
1 Boxwood rule, 2’, 4-fold .12
1 Barber’s ratchet brace, No. 33, 8” sweep 1.40
1 Miter-box, beech, 12” long, No. 00 .30
4 Brad awls, handled, 1”, 1¼”, 1½”, ½” .15
1 Set Russell Jennings Auger-bits, 4/16”, 5/16”, 6/16”,
7/16”, and 8/16” 1.40
1 Quire sandpaper, No. 00 .30
1 Quire sandpaper, No. 1 .30
----
Total $9.42
NOTE: Sufficient equipment for constructing all of these devices may be
found in average country homes. The work may be successfully done with
fewer tools but this list is given as a suggestion for schools.
LIST OF PUBLICATIONS FOR SUPPLEMENTARY READING
Farm Butter-making, Farmers’ Bulletin 541, U. S. Department of
Agriculture, Washington, D. C.
Butter-making on the Farm, Georgia State College of Agriculture,
Athens, Ga.
Butter-making, Storrs Experiment Station, Storrs, Conn.
Cheese-making, Wisconsin Experiment Station, Madison, Wis.,
Bulletin 181.
Neufchatel Cheese, Bulletin 78, Storrs Experiment Station, Storrs,
Conn.
Cottage or Dutch Cheese and Other Cheese, Oklahoma Agricultural
College, Stillwater, Okla.
Conveniences for Handling the Farm Cow and Her Products, Special,
U. S. Dept. of Agriculture, Office of the Secretary,
Washington, D. C.
The Production and Care of Milk and Cream, Special, U. S. Dept. of
Agri., Office of the Secretary, Washington, D. C.
A Plan for a Small Dairy House, Farmers’ Bulletin 689,
Department of Agriculture, Washington, D. C.
The Control of Chicken Mites and Lice, Iowa State College of
Agriculture, Ames, Iowa.
How to Care for the Little Chick, West Virginia University Agri.
Exp. Station, Morgantown, W. Va.
Suggestions on Poultry Raising for the Southern Farmer, Special,
U. S. Department of Agriculture, Office of the Secretary,
Washington, D. C.
Oregon Station Trap-Nest, Oregon Agricultural College, Corvallis,
Oregon.
A Simple Trap-Nest for Poultry, Farmers’ Bulletin 682, U. S.
Department of Agriculture, Washington, D. C.
The Organization of Boys’ and Girls’ Poultry Clubs, Farmers’
Bulletin 562, U. S. Department of Agriculture, Washington, D.
C.
Running Water for Farm Homes, A. & M. College, Agricultural
College, Miss.
Domestic Water Supply, Bulletin 215 by V. M. Cone, Special,
Colorado Extension Service, Fort Collins, Colorado.
Simple Water Supplies for the Farm, Extension Bulletin 18,
University of Nebraska, Lincoln, Nebr.
INDEX
Barrel, garbage, 74
Bath, shower, 80
Board, ironing, 19
Box, blacking, 61
Box, coal, 31
Boxes, dust, for poultry, 97
Box, wood, 37
Brooder, 98
Butter-making equipment, 99
Cabinet, wall, for kitchen, 17
Chariot, scrubbing, 75
Cheese-making equipment, 108
Cook stove drier, 34
Cooker, fireless, 39
Drainer, dish, 26
House, poultry, 84
Hopper, dry mash, for poultry No. 1, 89
Hopper, dry mash, for poultry No. 2, 92
Mop, dustless, 67
Nests, poultry, 85
Publications, list for supplementary reading, 116
Rack, cheese, 108
Rack, dish, 28
Rack, oat-sprouting trays, 95
Refrigerator, iceless, No. 1, 51
Refrigerator, iceless, No. 2, 55
Roller towel, 63
Screen, house, 49
Screen, sewing, 77
Sideboard, 46
Stand, umbrella, 58
Strainer, jelly, No. 1, 21
Strainer, jelly, No. 2, 24
Stool, milking, 106
Swing, porch, 65
Table, folding canning, 68
Table, vegetable paring, 15
Tester, egg, 86
Tools, suggested list, 115
Trap, fly, 71
Vessel, drinking, for poultry, 97
Wagon, roller tray, 43
Waterworks system, practical, 82
Woodworking, fundamentals in, 112
Worker, butter, 104
Transcriber’s Note:
Words and phrases in italics are surrounded by underscores, _like
this_. Those in bold are surrounded by equal signs, =like this=. Final
stops missing at the end of sentences and abbreviations were added.
The following were changed:
changed 5” to 5’, dimensions of iceless refrigerator No. 2
added “×” to 15” wide × 15” long
added “down” to halfway down the panel.
added “with” to “... outside of screen with burlap ...”
changed “1.10” to “⅒” in Narrow Ration Food recipe
changed “1.10” to “⅒” part meat in Narrow Ration Food recipe
*** END OF THE PROJECT GUTENBERG EBOOK HOME LABOR SAVING DEVICES ***
Updated editions will replace the previous one—the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg™ License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg™
electronic works
1.A. By reading or using any part of this Project Gutenberg™
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg™ electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg™ electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg™ electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg™ electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg™
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg™ electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg™ mission of promoting
free access to electronic works by freely sharing Project Gutenberg™
works in compliance with the terms of this agreement for keeping the
Project Gutenberg™ name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg™ License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg™ work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg™ License must appear
prominently whenever any copy of a Project Gutenberg™ work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this eBook or online
at www.gutenberg.org. If you
are not located in the United States, you will have to check the laws
of the country where you are located before using this eBook.
1.E.2. If an individual Project Gutenberg™ electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg™
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg™ electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg™ License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg™
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg™.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg™ License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg™ work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg™ website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg™ License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg™ works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg™ electronic works
provided that:
• You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg™ works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg™ trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, “Information about donations to the Project Gutenberg
Literary Archive Foundation.”
• You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg™
works.
• You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
• You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg™ work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg™ work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg™
Project Gutenberg™ is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg™’s
goals and ensuring that the Project Gutenberg™ collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg™ and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.
The Foundation’s business office is located at 809 North 1500 West,
Salt Lake City, UT 84116, (801) 596-1887. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.
Section 5. General Information About Project Gutenberg™ electronic works
Professor Michael S. Hart was the originator of the Project
Gutenberg™ concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg™ eBooks with only a loose network of
volunteer support.
Project Gutenberg™ eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our website which has the main PG search
facility: www.gutenberg.org.
This website includes information about Project Gutenberg™,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.
