Project Gutenberg's USDA Farmer's Bulletin 1460, by George M. Warren
This eBook is for the use of anyone anywhere in the United States and most
other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms of
the Project Gutenberg License included with this eBook or online at
www.gutenberg.org. If you are not located in the United States, you'll have
to check the laws of the country where you are located before using this ebook.
Title: USDA Farmer's Bulletin 1460
Simple Plumbing Repairs in the Home
Author: George M. Warren
Release Date: July 9, 2020 [EBook #62592]
Language: English
*** START OF THIS PROJECT GUTENBERG EBOOK USDA FARMER'S BULLETIN 1460 ***
Produced by Tom Cosmas
Transcriber Note
Text emphasis is denoted as _Italics_ and =Bold=. Whole and fractional
parts of numbers as 12-3/4.
U. S. DEPARTMENT OF AGRICULTURE
FARMERS' BULLETIN No. 1460
SIMPLE PLUMBING REPAIRS
IN THE HOME
PLUMBING often gets out of order, and upon prompt attention to the
little repair jobs depends its smooth, satisfactory operation. This
bulletin describes simple ways of doing little things, with the aid of
a few simple tools, to keep home plumbing in good working order.
Washington, D. C. Issued September 1925
Revised October 1936
SIMPLE PLUMBING REPAIRS IN THE HOME
By George M. Warren, _associate hydraulic engineer, Division of
Structures, Bureau of Agricultural Engineering_
CONTENTS
Page
Faucets 1
Stop and waste cocks 5
Ball cocks 6
Flush valves for low tanks 7
Clogged pipes 7
Thawing pipes 9
Removing scale from water hacks and coils 10
Leaks in pipes and tanks 11
Cracked laundry tubs 13
Hose menders or splicers 13
HOW BEST to make small plumbing repairs is a problem that comes to most
householders, as it is sometimes difficult to secure the services of
a plumber. In such situations a little knowledge on the part of the
householder often saves much delay, trouble, and expense. Where local
or State plumbing regulations are in force, and extensive repairs or
alterations are contemplated, the householder should make sure that the
work is duly authorized and is done by a properly qualified plumber.
Few persons realize the potential danger lurking in leaky waste pipes,
drains, and sewers, or in piping between systems, whereby sewage or an
impure water supply may even in the slightest degree gain access to a
potable water supply.
In making repairs it is often necessary to tighten or to loosen a screw
or nut, and the householder is sometimes uncertain in which direction
it should be turned. To screw or tighten an ordinary right-hand screw,
nut, or bolt, first think of the head of the part to be turned as being
the face of a clock and the screw driver or wrench as being the shaft
which turns the clock hands, and then rotate the tool from left to
right, in the same direction that the clock hands move. Conversely, to
unscrew or loosen, rotate the tool from right to left, in the direction
opposite to clockwise. Small brass screws and stems are easily twisted
off and rendered useless, especially if a large tool is used to turn
them. Undue strain should be avoided, as it may result in the part or
parts being broken at an unfortunate time.
FAUCETS
SEAT WASHERS
Badly worn washers make faucets noisy, hard to operate, and wasteful of
water. Moderate force on the handle of a faucet in good repair should
stop all flow and drip. Figure 1 shows an ordinary half-inch =T=-handle
compression faucet which closes against the pressure of the water. To
replace the seat washer, shut off the water to the faucet. Unscrew the
cap nut with a monkey wrench. (Placing cloth or thick paper between the
jaws of the wrench saves marring the cap nut.) Take hold of the faucet
handle and unscrew the stem from the body of the faucet. With a screw
driver remove the washer screw at the bottom of the stem. This screw is
often hard to start. Applying one or two drops of kerosene and lightly
tapping the head of the screw may help to loosen it in the stem. Use
strong, even force on the screw driver, the blade of which should have
a good square edge to fit the slot. The head of the screw often splits
before the shank of the screw turns in the stem, because it is already
corroded and weakened. If it splits, deepen the slot in the head with
a hacksaw, cutting a little into the shank of the screw. No harm is
done if the saw cuts slightly into the stem of the faucet. The washer
screw may now be turned with a small screw driver. Replace the old
washer with a new one, replace the washer screw, screw the stem into
the faucet, and screw down the cap nut. Rubber and fiber composition
washers for hot- or cold-water faucets cost 10 to 15 cents a dozen. A
"floating" washer, costing 15 cents, is very serviceable. A few washers
of the needed sizes should be kept in the home. If none are at hand, a
temporary washer may be cut from a piece of leather, rubber, or sheet
packing. Leather is preferable on cold-water faucets and rubber on
hot-water faucets.
[Illustration: Figure 1.--Compression faucet.]
[Illustration: Figure 2.--Compression faucet for a washstand.]
Figure 2 shows an ordinary 3/8-inch, 4-ball-handle compression faucet
for a washstand. To replace the seat washer, shut off the water to
the faucet and open the faucet one or two turns of the handle. With a
monkey wrench on the hexagonal part of the stuffing box unscrew the
stuffing box from the body of the faucet. Lift out the stem, replace
the old washer with a new one, as previously described, and screw the
stuffing box into the body.
A worn washer with constant leakage over the seat of a compression
faucet, together with grit lodging there, often causes the seat to
become cut, nicked, and grooved. The trouble occurs more often in
hot-water than in cold-water faucets. Such seats can easily be reground
or squared with a simple seat dressing tool, two types of which are
shown in figure 3, _A_ and _B_. A seat dresser with four cutters for
different-sized faucets costs about $2, and its use saves buying new
faucets. To dress the seat of a faucet, unscrew the stem from the
body to the faucet, as above described. Screw the adjustable, threaded
cone of the tool (see fig. 3, _A_) down into the body of the faucet,
as shown in figure 3, _C_, thus centering it over the seat. With the
hand, as shown in figure 3, _D_, gently rotate the wheel handle at the
top of the tool several times, and the cutter on the bottom of the stem
squares the seat. Turn the faucet bottom side up and shake out the
cuttings. Reassemble the faucet and turn on the water to wash out any
remaining cuttings.
[Illustration: Figure 3.--Faucet seat dressers: _A_, dresser with
inside adjustable cone; _B_, dresser with outside adjustable cone; _C_,
dresser A screwed into a compression faucet; _D_, rotating the wheel
handle and cutter.]
Seat washers are subject to damage from metal filings left in newly
installed water pipes. A good plumber, before screwing up a piece of
pipe, always stands the pipe on end and raps it with a hammer to clear
the bore.
Figure 4, _A_, shows an ordinary half-inch lever-handle Fuller faucet
which closes with the pressure. As shown in figure 4, _B_, the bottom
of the spindle is eccentric, so that slight turning of the handle moves
the rubber ball to and from the beveled seat. To replace the ball shut
off the water to the faucet. Unscrew the body from the tailpiece with
the hands or with a monkey wrench on the hexagonal part of the body of
the faucet. It may be necessary to apply a wrench to the hexagonal nut
on the tailpiece and press the wrench downward to prevent unscrewing
the tailpiece. Unscrew the stem nut, which holds the brass cap and
rubber ball on the stem. Put on a new ball and replace cap and nut. Red
rubber balls are considered to be better than black balls for hot-water
faucets. Avoid using too large a ball, as swelling of the rubber may
hinder the flow. Screw the faucet into the tailpiece. Just before the
joint closes or "makes up", wrap a little string packing or candle
wicking around the thread on the faucet to make the joint water-tight.
[Illustration: Figure 4.--Fuller faucet: _A_, body unscrewed from
tailpiece; _B_, spindle and stem removed from body.]
TOP WASHERS AND PACKINGS
A top washer or packing; snugly fitting the stem is necessary to
prevent leakage upward through the cap nut when a faucet is opened. If
the space is too tightly packed, the stem binds, nudging it hard to
operate the faucet; if too loosely packed, water spurts from the top of
the cap nut. Figure 5, _A_, shows a soft rubber-and-fabric top washer
suitable for the compression faucet shown in figure 1. This washer is
one-eighth of an inch thick and rests on the top of the body of the
faucet, making a water-tight joint when the cap nut is screwed down.
Just below the soft washer and inside the top of the body a thin brass
washer is placed to take the wear when the faucet is fully opened.
These washers are separated in the illustration but are together when
placed in a faucet.
[Illustration: Figure 5.--Top washers and packings: _A_, top washers
commonly used in ordinary compression faucets (fig. 1); _B_, top
washers which fill the space beneath the cap nut (fig. 1) _C_, candle
wick packing and brass washer for washstand faucet (fig. 2); _D_,
spindle packing for Fuller faucet (fig. 4).]
New faucets of the kind shown in figure 1 usually have the top washers
shown in figure 5, _B_. The rubber washer fills the space beneath the
cap nut, and the thin fiber and brass washers are for the purposes
described above. If no top washer is available, the space may be
packed with candle wicking or soft twine, to which a little mutton or
beef tallow should be applied to lubricate the stem, to preserve the
packing, and to make it more impervious to water.
When placing the top washer or washers on a compression faucet of
the kind shown in figure 1, it is unnecessary to shut off the water
provided the faucet is closed. With the right hand keep the faucet
closed and with a monkey wrench in the left hand unscrew the cap nut.
Unscrew the handle screw and remove handle and cap nut. Put on new
washers as shown in figure 5, _A_, or 5, _B_, and reassemble the parts.
Figure 5, _C_, shows the stem packing for the washstand faucet shown
in figure 2. The packing space is very small and is filled with candle
wicking lubricated with tallow. There is a thin brass friction washer
in the bottom of the stuffing box, and a hexagonal packing nut screws
into the top of the box. To renew the candle wicking, keep the faucet
closed. Unscrew the packing nut with a monkey wrench, wrap a little
wicking around the stem, and screw the packing nut down against the
wicking and into the stuffing box.
Spindle packing for a Fuller faucet (see fig. 4) is shown in figure 5,
_D_, and consists of three collars or rings obtainable from plumbing
dealers for a few cents. A lead ring or packing about one-eighth of an
inch long goes first (lowest) on the spindle; then a rubber-and-fabric
composition packing about one-fourth of an inch long; then a brass
packing about one-fourth of an inch long. Screwing down the cap nut
compresses the composition packing, and the metal packings take up
friction and wear. To put in new packings, shut off the water from the
faucet and remove the handle and cap nut, as described in connection
with compression faucets.
[Illustration: Figure 6.--Stop and waste cock; _A_, parts assembled;
_B_, parts unassembled.]
STOP AND WASTE COCKS
Figure 6, _A_, shows an adjustable socket-lever handle, ground key,
flat way, stop and waste cock to shut off water to part or all of a
piping system and to drain the higher situated pipes from which the
flow is cut off. A stop and waste should always be placed on the
house supply pipe just inside the house or the cellar wall. They are
very useful on branch pipes from a cellar or kitchen to upstairs
or back rooms subject to freezing temperatures or other temporary
discontinuance of the supply. Figure 6, _B_, shows the disassembled
parts, all of which except the handle are brass. The key or plug is
ground to a water-tight fit in the body of the cock, and water is
turned on or off by giving the handle a quarter turn. Turning the
handle crosswise of the pipe shuts off the supply, and the dead water
drains back through the small round hole in the side of the plug and
out the waste tube.
Many stop and waste cocks have broken or bent handles or are otherwise
rendered useless, because people do not understand them. As received
from dealers, the nut on the bottom of the plug is generally screwed up
tight, making it difficult or impossible to turn the handle and plug.
Long periods of disuse frequently cause the plug to stick fast in the
body. The plug is easily loosened by slightly unscrewing the bottom
nut and striking the lower end of the plug a few light blows with a
hammer. Slight leakage caused by wear of the plug or dirt around it
may be prevented by cleaning the plug and tightening the bottom nut. A
plug badly worn from long or continual use can be reground, but it is
usually better and cheaper to get a new plug or a complete new cock.
BALL COCKS
Figure 7, _A_, shows an ordinary compound-lever ball cock to control
the water supply in a flush tank. The float ball and the seat washer on
the bottom of the plunger are the only parts likely to need repairs.
The buoyancy of the float is the force which lowers the plunger,
shutting off the water as the tank fills. A leaky, water-logged float
holds the plunger up, permitting constant flow and waste of water. A
small leak in a copper float can be soldered; but if in bad condition,
the float should be replaced by a new one. A good copper, bakelite, or
hard-rubber float 4 by 5 inches costs 25 to 50 cents.
[Illustration: Figure 7.--Ball cock; _A_, parts assembled; _B_,
plunger, washer, and cap.]
Figure 7, _B_, shows the plunger and washer-holder cap which screws
on the bottom of the plunger. The washer should be of soft rubber or
leather, because the force which holds it to its seat is not heavy. The
cap is thin brass. To replace the washer, shut off the water and drain
the tank. Unscrew the two thumbscrews which pivot the float-rod lever
and plunger lever. Push the two levers to the left, drawing the plunger
lever through the head of the plunger. Lift out the plunger, unscrew
the cap on the bottom of the plunger, insert a soft, new washer, and
reassemble the parts. The cap may be so corroded and weakened that it
breaks during removal from the plunger. A new cap is then necessary,
and it is well to have one or two on hand. When putting a washer on a
ball cock, examine the seat to see that it is free of nicks and grit.
The seat may need regrinding, as explained under compression faucets.
FLUSH VALVES FOR LOW TANKS
Figure 8 shows a common type of flush valve for a low tank. Probably
no other plumbing in the home needs attention so often. It is under
water and subject to fouling and neglect. The hollow rubber ball gets
out of shape and fails to drop squarely into the hollowed seat. The
handle and lever fail to work smoothly or the lift wires get out of
plumb, causing the ball to remain up when it should drop to its seat.
To remove these difficulties, stop inflow to the tank by holding up
the float of the ball cock or supporting it with a stick. Drain the
tank by raising the rubber ball. If the ball is worn, out of shape,
or has lost its elasticity, unscrew the lower lift wire from the ball
and replace it with a new one. A 2-1/2-inch rubber ball costs about
25 cents, and a new one should always be kept in the house. The lift
wires should be straight and plumb. The lower lift wire is readily
centered over the center of the valve by means of the adjustable guide
holder. By loosening the thumbscrew, the holder is raised, lowered, or
rotated about the overflow tube! By loosening the lock nut and turning
the guide screw, the horizontal position of the guide is fixed exactly
over the center of the valve, these adjustments are very important.
The upper lift wire should loop into the lever armhole nearest to a
vertical from the center of the valve. A tank should empty within 10
seconds. Owing to lengthening of the rubber ball and insufficient rise
from its seat, the time may be longer than 10 seconds and the flush
correspondingly weak. This trouble may be overcome by shortening the
loop in the upper lift wire. A drop or two of lubricating oil on the
lever mechanism makes it work more smoothly.
[Illustration: Figure 8.--Flush valve for low tank.]
CLOGGED PIPES
Rust and dirt in water pipes are more or less successfully removed
as follows: Tie a piece of small, stout cord to each end of a 2-foot
length of small chain. Each piece of cord should be a little longer
than the length of pipe to be cleaned. Attach the free end of one of
the cords to a stiff steel wire and push the wire and cord through the
pipe. By means of the cords pull the chain back and forth through the
pipe, and then thoroughly flush the pipe with clean water under strong
pressure. Long lines may be opened at intervals and cleaned section by
section.
Other methods are: Using a swab or wire brush attached to a small steel
or brass rod; flushing with a powerful hand pump; or filling the pipe
with diluted muriatic acid and allowing it to stand in the pipe long
enough for the acid to act. If the treatment is unsuccessful it should
be repeated. A mixture of 1 part of acid and 7 parts of water allowed
to stand overnight in 1,000 feet of badly rusted 1-inch pipe has given
good results. After the acid treatment the pipe should be flushed long
and thoroughly with clean water to remove as fully as possible all
dirt, rust, and traces of acid.
When new piping is put in, abrupt turns are sometimes made with =T=
branches instead of elbows. The unused leg of the branch can be closed
with a screw plug, thus permitting easy access to the interior of the
pipe.
=Caution:= When a stop and waste (or valve) on a water service is
closed to permit cleaning or repairs, care should be taken to prevent
the formation of a vacuum in the high parts of the water piping and
the connections to plumbing fixtures; otherwise siphon action may draw
pollution from water closets having water-controlled or seat-operated
flush valves and from bathtubs, washbasins, laundry tubs, or other
fixtures in which the spout (discharge end of the water line) is lower
than the fixture rim, or worse, below the fixture overflow. Vacuum and
siphon action may be destroyed by opening the highest connected faucet
or an air cock in the top of the water line or by equipping the system
with suitable automatic vacuum breakers.
[Illustration: Figure 9.--Cleaning out a sink trap.]
All waste pipes and traps are subject to fouling. Dirt collects in
the bottom and grease adheres to the sides. The usual way of clearing
ordinary fixtures traps is to unscrew the clean-out ping, as shown
in figure 9, and wash out the obstructing matter or pull it out with
a wire bent to form a hook. Small obstructions are often forced down
or drawn up by the use of a simple rubber force cup (sometimes called
"the plumber's friend") costing 30 to 60 cents. This device is shown in
figure 10. The cup is placed over the fixture outlet and the fixture is
partially filled with water. The wood handle of the cup is then worked
rapidly down and up, causing alternate expulsion of the water from
beneath the cup and suction upward through the waste pipe and trap. If
a trap and the waste pipe from it are clogged with grease, hair, or
lint, it is best to open or disconnect the trap and dig out the greasy
matter with a stick. The use of chemical solvents in waste pipes is
explained in Farmers' Bulletin 1426, "Farm Plumbing."
[Illustration: Figure 10.--Rubber force cup.]
A variety of inexpensive flexible coil wire augers and sewer rods are
available for removing obstructions--mainly newspapers, rags, toilet
articles, grease, garbage, or other solids--from traps, waste pipes,
sewers, and drains. The growth of roots in sewers and drains causes
much trouble which better workmanship in making the joints would have
avoided. Augers and rods come in various sizes and lengths. Stock
lengths for clean-out augers for closet bowls are 3, 6, and 9 feet
and cost from $1 upward. Figure 11 shows two kinds of flexible augers
for general purposes. The upper is 4 feet long and has a small steel
cable from the handle to the wire hooks. The hooks can be drawn into
the coil, thus facilitating entry into a trap. The lower auger is 8
feet long, has a crank handle and corkscrew point generally preferred
for closet-bowl work. Placing a few sheets of toilet paper in the bowl
and then flushing usually indicates whether the obstruction has been
dislodged.
Flexible coil steel waste-pipe cleaners commonly come in diameters of
3/16, 1/4, 3/8, 1/2, and 5/8 inch and in lengths of 6, 9, 15, 25, 50,
and 100 feet. The 3/16-inch size in 9-foot length without handle or
corkscrew point costs about $1. The 1/4-inch size in 9-foot length with
automatic grip handle costs slightly more. The small sizes are very
useful in sink, lavatory, and bathtub traps and waste pipes.
Flat steel sewer rods, equipped with either an oval or a revolving
spear point and an automatic grip handle, come in stock lengths of
25, 50, 75, and 100 feet, in widths of 1/4 to 1-1/2 inches, and in
thicknesses of 1/16 and 1/8 inch. A rod 1/16 by 3/4 inch and 50 feet
long costs $4 to $5; a rod 1/8-inch thick, costing $5 to $8, is
desirable for ordinary sewer-cleaning purposes. Round sewer rods of
7/8-inch hickory or ash in 3- or 4-foot lengths with hook couplings
and simple sewer brushes and root cutters are described in Farmers'
Bulletin 1227, Sewage and Sewerage of Farm Homes.
[Illustration: Figure 11.--Coil spring augers.]
THAWING PIPES
The middle of a frozen pipe should never be thawed first, because
expansion of the water confined by ice on both sides may burst the
pipe. When thawing a water pipe, work toward the supply, opening a
faucet to show when the flow starts. When thawing a waste or sewer
pipe, work upward from the lower end to permit the water to drain away.
Applying boiling water or hot cloths to a frozen pipe is simple
and effective. Where there is no danger of fire a torch or burning
news-paper run back and forth along the frozen pipe gives quick
results. Underground or otherwise inaccessible pipes may be thawed as
follows: Open the frozen water pipe on the house end. Insert one end
of a small pipe or tube. With the aid of a funnel at the other end of
the small pipe pour boiling water into it and push it forward as the
ice melts. A piece of rubber tubing may be used to connect the funnel
to the thaw pipe. Hold the funnel higher than the frozen pipe, so
that the hot water has head and forces the cooled water back to the
opening, where it may be caught in a pail. The head may be increased
and the funnel may be more conveniently used if an elbow and a piece of
vertical pipe are added to the outer end of the thaw pipe, as shown in
figure 12. Add more thaw pipe at the outer end until a passage is made
through the ice. Withdraw the thaw pipe quickly after the flow starts.
Do not stop the flow until the thaw pipe is fully removed and the
frozen pipe is cleared of ice. A small force pump is often used instead
of a funnel and is much to be preferred for opening a long piece of
pipe. If available, a jet of steam may be used instead of hot water;
being hotter, it is more rapid.
[Illustration: Figure 12.--Thawing a frozen pipe.]
Frozen traps and waste pipes are sometimes thawed by pouring in caustic
soda or lye, obtainable at grocery stores for about 25 cents per pound.
Chemicals of this character should be labeled "Poison" and should be
kept where children cannot get them. To prevent freezing, the water
in the traps of a vacant house should be removed during cold weather,
and the traps should be filled with kerosene, crude glycerin, or a
very strong brine made of common salt and water, or other substance
mentioned in Farmers' Bulletin 1426, Farm Plumbing.
REMOVING SCALE FROM WATER BACKS AND COILS
Hard water causes a limy deposit or scale on the inside of water backs
and heating coils. If allowed to accumulate the scale retards the
circulation and heating of the water and, by closure of the bore, may
prove dangerous. Moreover, continued neglect makes it increasingly
difficult to remove the scale.
The water back or coil should be removed from the fire box. At the
union or other joints nearest the fire box disconnect all pipes and
unscrew them from the water back. If there is a clamp which holds the
fire-brick lining against the oven, loosen it and remove side and
end linings. Lift out the water back and take it out on the ground.
Soft scale or sludge may be removed by pounding the water back with
a mallet or hammer and then flushing with a strong jet of water. A
long gouge or chisel is used on those surfaces that can be reached.
Sometimes the water back is heated in a blacksmith's forge and then
pounded, but unless carefully done this treatment may break it. Some
householders keep a spare water back for use while the other is being
cleaned.
Waters of varying chemical composition cause scale differing in
composition and hardness. Ordinary limestone (calcium carbonate) scale,
if not of excessive thickness, may readily be removed with muriatic
acid. Gypsum (calcium sulphate) scale is hard and resistant and with
other constituents in their more compact forms is little affected by
muriatic acid. The water back should be laid on the ground and filled
with a strong solution of the acid in water. The strength of the
solution should vary with the amount of deposit, the ordinary mixture
being 1 part of acid and 5 to 7 parts of water. If the deposit is very
thick, the acid needs little dilution. Commercial muriatic acid in
bottles containing 6 pounds (about 2-1/2 quarts) costs 20 to 25 cents a
pound. The bottle should be labeled "Muriatic acid--poison"; and, like
the chemicals previously mentioned, it should be kept where children
cannot get it. Heating the water back hastens the action of the acid.
At the end of an hour or two, or sooner if the deposit is dissolved,
pour the solution from the water back and flush it thoroughly with hot
water to remove the acid. If all the deposit has not been removed,
repeat the operation, making sure that the acid is completely washed
out before replacing the water back. In replacing the water back it is
important to have it level, using a spirit level for this purpose.
Similar methods may be used with copper coils. Place the coil (or
heater) on two sticks over a large bowl. With the aid of a lead funnel
pour the acid solution down through the coil. Dip from the bowl and
continue to circulate the solution through the coil until the deposit
is dissolved. The coil should then be thoroughly washed out with hot
water.
The hot-water flow pipe close to a water back or coil frequently
becomes thickly covered with scale. If the pipe is brass, it may be
disconnected and treated with acid and then washed out with hot water.
If the pipe is galvanized iron and in bad condition, it will probably
be more satisfactory to replace it with new pipe.
LEAKS IN PIPES AND TANKS
A small leak in a water pipe can be stopped in an emergency as follows:
Place a flat rubber or leather gasket over the leak and hammer a piece
of sheet metal to fit over the gasket; secure both to the pipe with
a clamp obtainable at hardware or 5-and-10-cent stores. A small leak
under low pressure is sometimes stopped by shutting off the water
and then embedding the pipe in richly mixed portland-cement mortar
or concrete. Broken sewer pipe can be repaired in like manner, and a
wrapping of wire netting embedded in the mortar or concrete increases
its strength. However, it is better to relay the sewer and make all
joints water-tight and root-proof as described in Farmers Bulletin
1227, Sewage and Sewerage of Farm Homes. A small hole in cast-iron pipe
may be tapped for a screw plug.
Where a leaky screw joint cannot be tightened with a pipe wrench, the
leak is sometimes stopped with a blunt, chisel or calking tool and
hammer. Sometimes a crack or hole is cleaned out and then plugged and
calked with lead, or a commercial iron cement mixed to the consistency
of stiff putty. Sometimes a pipe band, a clamp with two bolts (similar
to but stronger than the one shown in fig. 14), or a split sleeve is
employed to hold a thin coating of iron cement or a gasket over a leak.
If the leak is at a screw joint, the band is usually coated inside with
one-eighth of an inch of iron cement and then slipped over the pipe.
Keeping the bolt farthest from the coupling or fitting a little tighter
than the other, both bolts, are tightened. During the tightening, the
band should be driven with a hammer snugly against the coupling or
fitting.
In addition to these methods and devices, there are several kinds of
good, inexpensive, ready-made pipe and joint repairers obtainable of
manufacturers and dealers.
A corroded and leaky spot in a steel tank or range boiler can be closed
with an inexpensive repair bolt or plug obtainable from dealers. Figure
13 shows a home-made repairer consisting of a three-sixteenths by
3-inch toggle bolt costing 10 cents and a flat rubber gasket, brass
washer, and nut. The link of the bolt, after being passed through the
hole, takes an upright position, and screwing up the nut forces the
gasket tightly against the outside of the boiler.
[Illustration: Figure 13.--Home-made repairer; _A_, passing the link of
the toggle bolt through the hole (enlarged) in the tank; _B_, side view
of edge of tank with bolt, washers, and nut after being tightened; _C_,
outside view of completed job.]
A small hole must be reamed or enlarged with a round file to a diameter
of about five-eighths inch. The metal beneath the gasket should be
firm and clean. A little candlewick packing may be wrapped around the
bolt to prevent leakage along the bolt. Sometimes a hole is closed by
driving in a tapered steel pin to turn the metal inward, forming a
surface which can be tapped for an ordinary screw plug. A hole in the
wall of a tank or pipe having considerable thickness can be easily and
quickly closed by screwing in a tapered steel tap plug which cuts and
threads its way through the wall. These plugs in different sizes are
obtainable of dealers and a monkey wrench is the only tool required to
insert them; it is unnecessary to shut off or drain the water from the
tank or pipe.
A small leak at a seam or rivet can often be closed by merely rubbing a
cold chisel along the beveled edge of the joint. Do not attempt to calk
a seam unless the plates have considerable thickness and the rivets are
closely spaced and are close to the calking edge, and then use extreme
caution. Run a regular calking tool or blunt chisel along the beveled
edge, tapping the tool very lightly with a light hammer to force the
edge of the upper plate against and into the lower plate.
CRACKED LAUNDRY TUBS
Cracks in slate, soapstone, or cement laundry tubs are made water-tight
with a mixture of litharge and glycerin or a specially prepared
commercial cement. The litharge and glycerin are mixed and stirred to
form a smooth heavy paste free from lumps. The crack should be cleaned
out to remove all grease and dirt and the paste should be worked into
the crack with a case knife. A paste of portland cement and water, or
of the white of an egg and fresh lump lime, has been used successfully
for this purpose.
[Illustration: Figure 14.--Hose menders: Above, hose mender and hose
coupling; below, two pieces of hose joined with a mender. The left-hand
piece is fastened with wire twisted with a pair of pliers, and the
right-hand piece is clamped.]
HOSE MENDERS OR SPLICERS
A break in garden hose can be quickly repaired or two pieces of hose
can be joined with a 10- or 15-cent iron or brass hose mender or
splicer shown in figure 14 (upper left). Cut off the defective piece of
hose, insert the mender in the good ends of the hose, and wire or clamp
the hose as shown in figure 14 (below). Menders come to slip inside of
1/2-, 3/4-, or 1-inch hose. The regular brass hose coupling shown in
figure 14 (upper right), which costs 25 to 40 cents, can be used for
this purpose.
U. S. GOVERNMENT PRINTING OFFICE: 1946
For sale by the Superintendent of Documents,
U. S. Government Printing Office
Washington 25 D. C. -- Price 5 cents
* * * * *
Transcriber Note
Illustrations were repositioned so as to not split paragraphs.
End of Project Gutenberg's USDA Farmer's Bulletin 1460, by George M. Warren
*** END OF THIS PROJECT GUTENBERG EBOOK USDA FARMER'S BULLETIN 1460 ***
***** This file should be named 62592.txt or 62592.zip *****
This and all associated files of various formats will be found in:
http://www.gutenberg.org/6/2/5/9/62592/
Produced by Tom Cosmas
Updated editions will replace the previous one--the old editions will
be renamed.
Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg-tm electronic works to protect the PROJECT GUTENBERG-tm
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for the eBooks, unless you receive
specific permission. If you do not charge anything for copies of this
eBook, complying with the rules is very easy. You may use this eBook
for nearly any purpose such as creation of derivative works, reports,
performances and research. They may be modified and printed and given
away--you may do practically ANYTHING in the United States with eBooks
not protected by U.S. copyright law. Redistribution is subject to the
trademark license, especially commercial redistribution.
START: FULL LICENSE
THE FULL PROJECT GUTENBERG LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg-tm mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase "Project
Gutenberg"), you agree to comply with all the terms of the Full
Project Gutenberg-tm License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project
Gutenberg-tm electronic works
1.A. By reading or using any part of this Project Gutenberg-tm
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg-tm electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg-tm electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the
person or entity to whom you paid the fee as set forth in paragraph
1.E.8.
1.B. "Project Gutenberg" is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg-tm electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg-tm electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg-tm
electronic works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation ("the
Foundation" or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg-tm electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg-tm mission of promoting
free access to electronic works by freely sharing Project Gutenberg-tm
works in compliance with the terms of this agreement for keeping the
Project Gutenberg-tm name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg-tm License when
you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg-tm work. The Foundation makes no
representations concerning the copyright status of any work in any
country outside the United States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg-tm License must appear
prominently whenever any copy of a Project Gutenberg-tm work (any work
on which the phrase "Project Gutenberg" appears, or with which the
phrase "Project Gutenberg" is associated) is accessed, displayed,
performed, viewed, copied or distributed:
This eBook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no
restrictions whatsoever. You may copy it, give it away or re-use it
under the terms of the Project Gutenberg License included with this
eBook or online at www.gutenberg.org. If you are not located in the
United States, you'll have to check the laws of the country where you
are located before using this ebook.
1.E.2. If an individual Project Gutenberg-tm electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase "Project
Gutenberg" associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg-tm
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3. If an individual Project Gutenberg-tm electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg-tm License for all works
posted with the permission of the copyright holder found at the
beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg-tm
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg-tm.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg-tm License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg-tm work in a format
other than "Plain Vanilla ASCII" or other format used in the official
version posted on the official Project Gutenberg-tm web site
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original "Plain
Vanilla ASCII" or other form. Any alternate format must include the
full Project Gutenberg-tm License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg-tm works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg-tm electronic works
provided that
* You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg-tm works calculated using the method
you already use to calculate your applicable taxes. The fee is owed
to the owner of the Project Gutenberg-tm trademark, but he has
agreed to donate royalties under this paragraph to the Project
Gutenberg Literary Archive Foundation. Royalty payments must be paid
within 60 days following each date on which you prepare (or are
legally required to prepare) your periodic tax returns. Royalty
payments should be clearly marked as such and sent to the Project
Gutenberg Literary Archive Foundation at the address specified in
Section 4, "Information about donations to the Project Gutenberg
Literary Archive Foundation."
* You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg-tm
License. You must require such a user to return or destroy all
copies of the works possessed in a physical medium and discontinue
all use of and all access to other copies of Project Gutenberg-tm
works.
* You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
* You comply with all other terms of this agreement for free
distribution of Project Gutenberg-tm works.
1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg-tm electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from both the Project Gutenberg Literary Archive Foundation and The
Project Gutenberg Trademark LLC, the owner of the Project Gutenberg-tm
trademark. Contact the Foundation as set forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg-tm collection. Despite these efforts, Project Gutenberg-tm
electronic works, and the medium on which they may be stored, may
contain "Defects," such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the "Right
of Replacement or Refund" described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg-tm trademark, and any other party distributing a Project
Gutenberg-tm electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you 'AS-IS', WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg-tm electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg-tm
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg-tm work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg-tm work, and (c) any
Defect you cause.
Section 2. Information about the Mission of Project Gutenberg-tm
Project Gutenberg-tm is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg-tm's
goals and ensuring that the Project Gutenberg-tm collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg-tm and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at
www.gutenberg.org
Section 3. Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation's EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state's laws.
The Foundation's principal office is in Fairbanks, Alaska, with the
mailing address: PO Box 750175, Fairbanks, AK 99775, but its
volunteers and employees are scattered throughout numerous
locations. Its business office is located at 809 North 1500 West, Salt
Lake City, UT 84116, (801) 596-1887. Email contact links and up to
date contact information can be found at the Foundation's web site and
official page at www.gutenberg.org/contact
For additional contact information:
Dr. Gregory B. Newby
Chief Executive and Director
[email protected]
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg-tm depends upon and cannot survive without wide
spread public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular
state visit www.gutenberg.org/donate
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg Web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate
Section 5. General Information About Project Gutenberg-tm electronic works.
Professor Michael S. Hart was the originator of the Project
Gutenberg-tm concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg-tm eBooks with only a loose network of
volunteer support.
Project Gutenberg-tm eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.
Most people start at our Web site which has the main PG search
facility: www.gutenberg.org
This Web site includes information about Project Gutenberg-tm,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.
