Project Gutenberg's A Study of Splashes, by Arthur Mason Worthington
This eBook is for the use of anyone anywhere at no cost and with
almost no restrictions whatsoever. You may copy it, give it away or
re-use it under the terms of the Project Gutenberg License included
with this eBook or online at www.gutenberg.org
Title: A Study of Splashes
Author: Arthur Mason Worthington
Release Date: May 28, 2012 [EBook #39831]
Language: English
*** START OF THIS PROJECT GUTENBERG EBOOK A STUDY OF SPLASHES ***
Produced by Jana Srna, Alexander Bauer, Erica
Pfister-Altschul, and the Online Distributed Proofreading
Team at http://www.pgdp.net (This file was produced from
images generously made available by The Internet
Archive/American Libraries.)
A STUDY OF SPLASHES
_BY THE SAME AUTHOR._
* * * * *
A FIRST COURSE OF PHYSICAL LABORATORY
PRACTICE.
CONTAINING 264 EXPERIMENTS.
_With Illustrations. Crown 8vo, 4s. 6d._
* * * * *
DYNAMICS OF ROTATION.
AN ELEMENTARY INTRODUCTION TO RIGID DYNAMICS.
_Crown 8vo, 4s. 6d._
* * * * *
LONGMANS, GREEN, AND CO.
LONDON, NEW YORK, BOMBAY, AND CALCUTTA.
[Illustration: Permanent Splashes left where a Projectile has
entered an Armour-plate. [_See page 120._]
A STUDY OF SPLASHES
BY
A. M. WORTHINGTON
C.B., M.A., F.R.S.
HEADMASTER AND PROFESSOR OF PHYSICS
AT
THE ROYAL NAVAL ENGINEERING COLLEGE, DEVONPORT
WITH 197 ILLUSTRATIONS FROM INSTANTANEOUS PHOTOGRAPHS
LONGMANS, GREEN, AND CO.
39 PATERNOSTER ROW, LONDON
NEW YORK, BOMBAY, AND CALCUTTA
1908
_All rights reserved_
DEDICATED
TO
THE NATURAL HISTORY SOCIETY OF RUGBY SCHOOL
AND ITS FORMER PRESIDENT
ARTHUR SIDGWICK
IN REMEMBRANCE OF THE ENCOURAGEMENT
GIVEN TO THE EARLY OBSERVATIONS MADE IN BOYHOOD
BY MY OLD SCHOOL-FRIEND
H. F. NEWALL
FROM WHICH THIS STUDY SPRANG.
PREFACE
This publication is an attempt to present in a form acceptable to the
general reader the outcome of an inquiry conducted by the aid of
instantaneous photography, which was begun about fourteen years ago. The
author, in 1894, had occasion to lecture at the Royal Institution on the
"Splash of a Drop," of which he had already made a somewhat prolonged
study. That lecture, which was subsequently reprinted in the "Romance of
Science" series by the Society for Promoting Christian Knowledge, dealt
largely with the splash of a drop falling on a solid plate, with which
the present volume is not concerned. At the close of the lecture were
exhibited for the first time a few photographs of some of the phenomena
now dealt with, which the author had just succeeded in taking with the
help of his friend Mr. R. S. Cole. The success of the photographs and
the additional information they afforded led to a long photographic
investigation, which formed the subject of two papers[A] in the
_Transactions_ of the Royal Society. Except for two magazine
articles,[B] the results of this work have not been presented to the
general public. Moreover, in the illustrations printed by the Royal
Society much of the beauty of the original photographs was lost in the
reproduction, or was sacrificed in a selection of which the only object
was the elucidation of points of technical scientific interest.
If the present volume is so fortunate as to find many readers among the
general public, as the author hopes it may, especially among the young
whose eyes are still quick to observe, and whose minds are eager, it
will be on account of admiration for the exquisite beauty of some of the
forms assumed, of surprise at the revelation of so much where so little
was expected, and because of the peculiar fascination that is always
felt in following any gradually changing natural phenomenon, in which
the sequence of events can, partly at any rate, be anticipated and
understood.
For the sake of serious students of Physics who may be interested in
unexpected phenomena of fluid motion, all references that seem necessary
have been given in footnotes, and it may be mentioned that the later
photographs of Series I and those of Series I-a and III, have not been
previously published, and afford new information on certain points.
In taking these photographs the author has been much helped by his
friends Dr. G. B. Bryan and Mr. G. F. Page.
A. M. W.
TAVISTOCK, _Sept. 18, 1907_.
[Added _March 1, 1908_.] A slight delay in the publication of this book
has afforded the opportunity of obtaining the new and quite unexpected
information given in the supplementary chapter.
CONTENTS
PAGE
CHAPTER I
PRELIMINARY--METHODS OF OBSERVATION AND APPARATUS 1
CHAPTER II
THE SPLASH OF A DROP--LOW FALL 15
CHAPTER III
PRINCIPLES INVOLVED 32
CHAPTER IV
THE SPLASH CONTINUED 41
CHAPTER V
HIGHER FALLS--BUBBLE-BUILDING 53
CHAPTER VI
BELOW THE SURFACE 69
CHAPTER VII
THE TWO KINDS OF SPLASHES OF SOLID SPHERES 73
CHAPTER VIII
THE TRANSITION FROM THE SMOOTH OR "SHEATH" SPLASH
TO THE ROUGH OR "BASKET" SPLASH 95
CHAPTER IX
THE EXPLANATION OF THE CAUSE OF DIFFERENCE BETWEEN
THE TWO SPLASHES 108
CHAPTER X
CONCLUSION 118
CHAPTER XI
(SUPPLEMENTARY)
A NEW PHENOMENON THAT APPEARS WITH AN INCREASE IN
THE VELOCITY OF ENTRY OF A ROUGH SPHERE 121
FOOTNOTES:
[A] "Impact with a Liquid Surface," by Worthington and Cole. _Phil.
Trans. Roy. Soc._, A 193, 1897, and A 255, 1900.
[B] _Pearson's Magazine_, July and August, 1898.
A STUDY OF SPLASHES
CHAPTER I
PRELIMINARY--METHODS OF OBSERVATION AND APPARATUS
There will be but few of my readers who have not, in some heavy shower
of rain, beguiled the tedium of enforced waiting by watching, perhaps
half-unconsciously, the thousand little crystal fountains that start up
from the surface of pool or river; noting now and then a surrounding
coronet of lesser jets, or here and there a bubble that floats for a
moment and then vanishes.
It is to this apparently insignificant transaction, which always has
been and always will be so familiar, and to others of a like nature,
that I desire to call the attention of those who are interested in
natural phenomena; hoping to share with them some of the delight that I
have myself felt, in contemplating the exquisite forms that the camera
has revealed, and in watching the progress of a multitude of events,
compressed indeed within the limits of a few hundredths of a second, but
none the less orderly and inevitable, and of which the sequence is in
part easy to anticipate and understand, while in part it taxes the
highest mathematical powers to elucidate.
In these modern days of kinematographs and snapshot cameras it might
seem an easy matter to follow, by the aid of photography, even a
splashing drop. But in reality the task is not so simple, for the
changes of form that take place in a splash are far too rapid to come
within reach of any ordinary kinematograph, and even the quickest
photographic shutter is also much too slow, so that it is necessary to
have recourse to the far shorter exposure of a suitable electric spark.
The originals of the photographs which illustrate this book were
taken by means of a spark, whose duration was certainly less than
three-millionths of a second, an interval of time which bears to a whole
second about the same proportion as a day to a thousand years.
In order to obtain the photographs, advantage was taken of the fact that
whatever be the sequence of events in any particular splash, this
sequence will be exactly repeated every time that a falling drop strikes
the surface under exactly the same conditions, and the problem to be
solved was, therefore, as follows:--To cause a drop of definite size to
fall from a definite height in absolute darkness so as to strike the
surface of the liquid into which it falls at a spot towards which is
directed a photographic camera with uncovered lens, and armed with an
exceptionally sensitive plate, and to illuminate the drop at the instant
that it just touches the surface by a flash of such excessively short
duration that no appreciable change of form can take place while the
drop is illuminated.
This gives us a photograph of the earliest stage. The plate must then be
removed and a fresh one substituted; a second drop, of exactly the same
size, must be let fall from exactly the same place, and photographed in
just the same way, but the flash must now be so timed as to take place
at a slightly later stage of the splash, say, one-thousandth of a second
later. The photographic plate must be then again removed and a third
substituted, on which a still later stage is to be depicted, and in this
way the phenomenon can be followed step by step.
By adopting this process, and not attempting to follow the same
individual splash throughout, we avoid two great difficulties: (1) the
necessity of shifting our photographic plate or film through a distance
equal to the breadth of the whole picture every five hundredth or
thousandth of a second (if we wish to obtain pictures of stages so near
together as this); and (2) the difficulty of obtaining brilliant flashes
of light of sufficiently short duration at these very short intervals.
For these we substitute two other difficulties: (1) that of delivering
the drops exactly as required; and (2) that of timing the flash on each
occasion within one or two thousandths of a second, so as to pick out
the exact stage we wish to photograph.
I will now describe how these two problems have been solved.
It is easy enough to arrange for the production of small drops of almost
exactly equal size. They may be allowed to fall one by one at a steady
rate from the end of a fine glass tube connected to a vessel in which
the liquid is maintained at a constant level, as in Fig. 1, or they may
be squeezed out slowly as required by means of a syringe held in a clip
as in Fig. 2. Any required number of these small drops can be caught,
and allowed to run together if a larger drop is to be experimented with.
[Illustration: FIG. 1]
[Illustration: FIG. 2]
If the liquid used is mercury, the drops may be caught in any little
glass cup such as a deeply concave watch-glass; but other liquids, such
as water or milk, would wet the glass and stick to it.
If, however, the inside surface of the watch-glass be first carefully
smoked in the flame of a candle, then even water or milk will roll over
it without sticking, and the drop thus made up will retain a spheroidal
form, and can be conveyed to the place of observation in the dark room,
where it is transferred to the "dropping cup."
This consists of a similar, deep, smoked watch-glass (W)--see Plate
I--supported on the end of a small horizontal lever, a light cylindrical
rod of about the dimensions of an ordinary uncut lead pencil, pivoted
about a horizontal axle near the end to which the watch-glass is
attached. The other end is armed with a small light piece of iron (I)
and is held in position by means of an electro-magnet (M), against the
action of a spring. On cutting off the current from the electro-magnet
the spring, acting as a catapult, tosses up the longer arm of the lever
and thus removes the watch-glass from below the drop (D), which is left
unsupported in mid-air, so that it falls from a definite fixed distance
into a bowl of water placed below it, towards the surface of which the
camera (C) is directed. This solves problem number one. Of course, if we
wish to observe the splash of a solid sphere, there is no need to smoke
the surface of the watch-glass. Indeed, the sphere may be more
conveniently supported on a small ring.
Now for the production and timing of the flash. Two large Leyden jars
(JJ) are provided, and charged by an electrical machine on their inner
coats, one positively and one negatively. Stout wires lead from the
outer coats to the dark room, and terminate in a spark-gap (S) between
magnesium terminals close over the surface of the water in the bowl just
mentioned. If the inner coats are now connected together, the positive
and negative charges unite with a dazzling flash and a simultaneous
discharge and flash takes place between the two outer coats across the
spark-gap in the dark room.
This latter is the illuminating spark; we have now to time it correctly.
For this purpose it is arranged that the discharge shall be effected by
means of a falling metal sphere (T) which I shall call the timing
sphere, which passes between two terminals S and S connected one to the
inside of one jar and one to the inside of the other. These terminals
are just too far apart for a spark to leap across, till the timing
sphere passes between them and thus shortens the gap; then the discharge
takes place, with its accompanying flash in the dark room.
The release of the timing sphere is effected by an arrangement of lever
and spring controlled by an electro-magnet exactly similar to that which
releases the drop in the dark room, and the two electro-magnets _are on
the same electric circuit_, so that the drop and timing sphere _are
released simultaneously_. But while the drop always falls the same
distance, the height through which the timing sphere has to fall before
producing discharge can be adjusted at will, and to great nicety, by
moving its releasing-lever up or down a vertical support with a scale
attached.
If, for example, a particular stage of the splash is photographed when
the timing sphere falls just four feet to the gap, then by raising its
releasing-lever about two-fifths of an inch, the laws of falling bodies
tell us that we shall postpone the flash by just one-thousandth of a
second, and the next photograph will accordingly reveal a stage just so
much later.
[Illustration: PLATE I
Arrangement of apparatus for photographing splashes.
LABORATORY
E is the electrical machine.
J J are the Leyden jars whose inner coats are connected to the
sparking knobs S S.
L is the lever for releasing the timing sphere T.
C is the catapult.
I is the light strip of iron held down by the electro-magnet M.
DARK ROOM
D is the drop resting on the smoked watch-glass W.
M is the electro-magnet holding down the lever against the
action of the catapult, by means of the thin strip of iron
I.
C is the camera directed towards the liquid L into which the
drop will fall.
S is the spark-gap between magnesium terminals connected to the
outer coats of the Leyden jars.
R is the concave mirror.]
It ought still to be mentioned that to make the utmost use of the
illuminating power of the spark, it is necessary to place close behind
it a little concave mirror (R), by means of which a compact beam of
rays, which would otherwise have been wasted, is directed to the
required spot. By this addition we imitate, in miniature, the
search-light of a man-of-war.
* * * * *
As with all experimental devices, the precision attainable with this
arrangement is limited by several circumstances. In the first place, the
demagnetization of the iron cores of the electro-magnets, when the
current is cut off, is not truly instantaneous, and the time required
depends on the strength of the magnetizing current and on the
temperature of the iron, which in turn will depend on the length of time
for which the current has been running. This variation would be of no
importance if the two magnets were exactly alike and the springs of
exactly equal strength, conditions which can be nearly but not perfectly
fulfilled.
[Illustration: PLATE II
Photographs taken to test the accuracy of the "timing."
1 2 3 4 5]
A more important source of uncertainty arises from the fact that the
time at which the spark takes place depends partly on the magnitude of
the + and - charges which have been allowed to accumulate on the
discharging knobs connected to the two Leyden jars, for when these
charges are larger, then the spark will be longer and will take place
earlier and before the timing sphere has reached the mid-position. The
charging has therefore to be carefully watched by means of the
indications of a suitable electrometer, and the timing sphere must on
each occasion be released when the charges have just reached the right
value. But even this does not entirely suffice, for the passage of the
spark depends also partly on the state of the surface of the knobs,
which cannot be kept at any high degree of polish.
Still, when care is taken to keep the conditions as nearly as possible
constant, neither of these sources of error is serious, and the reader
can judge for himself of the accuracy of the timing from the photographs
given on Plate II, in which a solid sphere was let fall in the dark room
past a metre scale. The timing sphere was arranged, in the first four
photographs, to illuminate it at the same stage in its fall, after a
descent of thirty centimetres; if the timing had been perfect the sphere
would appear on each occasion at the same mark on the scale.
It will be observed that in the first, second, and fourth photographs
the falling sphere is almost accurately bisected by the long line of the
three-inch mark on the right-hand edge of the scale. The greatest
difference of position being just about one millimetre (as read off the
left-hand scale), which would correspond to an error of about 1/2700 of
a second. But the third photograph is earlier, showing the sphere 4·5
millimetres higher up, a distance which implies an error of just 1/600
of a second.
A fifth photograph was then taken, with the timing arranged so as to
illuminate the sphere one centimetre higher up, and it will be seen that
if we compare this with No. 3, the error is again only one millimetre.
Thus Nos. 3 and 5 agree very closely, but disagree with Nos. 1, 2, and 4
by about 1/600 of a second.
The photographs themselves supply the reason. For there happens to be
visible on each an (out-of-focus) image of the spark, and this image is
very much the same in 1, 2 and 4, but much larger and brighter in 3 and
5, showing that the knobs were then more highly charged, which would
account for the spark occurring a little too early.
But when we are watching the splash made by the fall of a liquid drop,
instead of a solid sphere, there is a new and more serious source of
difficulty. For the drop as it lies on the smoked glass cup is not
perfectly spherical, but is flattened by its own weight, as shown in
Fig. 3, and on the sudden removal of the supporting cup it oscillates
between an oval form, elongated vertically, and a flattened form (see
Fig. 4). These oscillations are unavoidable, and their extent will
depend partly on the amount of adhesion between the smoked surface and
the drop, and as this adhesion is never entirely absent and is variable,
depending partly on the length of time that the drop has been lying in
the cup, it follows that the drop will always receive a slight tug
downwards at starting, which will be greater on some occasions than on
others. On this account not only will the time taken to reach the water
vary slightly, but the drop will strike it sometimes when elongated and
sometimes when flattened, and the resulting splash will be affected by
this circumstance.
[Illustration: FIG. 3]
[Illustration: FIG. 4]
The four photographs on the next page were taken in succession in order
to afford the reader an opportunity of judging for himself the sort of
accuracy attainable when a liquid drop was concerned.
The fall was 30 centim., and the greatest discrepancy is 4·8
millimetres, corresponding to 1/560 of a second. Thus even here the
error does not amount to two-thousandths of a second.
[Illustration: Photographs taken to test the timing of a falling
drop.
1 2 3 4]
With higher falls the timing sphere is moving more quickly past the
discharging knobs, and the error due to a longer or shorter spark is
correspondingly less, so that it appears safe to say that the accuracy
of the timing was such that, when all precautions were taken, any
desired stage could be picked out within two-thousandths of a second.
It is not however pretended that the precautions necessary for the most
accurate timing were always taken, especially in the earlier Series of
Photographs, for the main object of the experiments was to find out
what happened, and only incidentally to ascertain exactly how long it
took to happen, and there is no doubt that on some occasions, through
the smoke-film being allowed to wear away, adhesions to the dropping cup
occurred, with a corresponding disturbance of the timing, before the
defect was noticed and remedied.
[Illustration: FIG. 5
Photograph of the edge of a rapidly whirling disc.]
It remains to mention, for the sake of those interested in photography,
that notwithstanding the sensitiveness of the plates and the brilliance
of the illuminating spark, its duration was so short that the negatives
were always "under-exposed."[C] I have mentioned that the effective
duration of the spark was less than three-millionths of a second. The
evidence for this is the accompanying photograph (Fig. 5), taken of a
cardboard disc when rotating at a rate of fifty-three turns per second;
the disc was 22 cm. in diameter, and had been roughly graduated round
the edge with pen and ink. The photograph of the part that was in focus
shows no perceptible blurring of the edge of the marks, and with a lens,
a blurring of one-tenth of a millimetre would be easily detectable.
Since the edge was moving at a rate of 36·5 metres per second (about 78
miles per hour), the time taken to traverse one-tenth of a millimetre
would be rather less than three-millionths of a second. Hence we may
conclude that the illumination did not last so long as this.
The weakness of the negatives was met by a prolonged development of
about forty minutes in a saturated solution of eikonogen. This forbade
the use of any artificial light, and all the photographic processes had
to be conducted in absolute darkness. To avoid the tedium of long
waiting in the dark room, a light-tight tray was constructed, in which
several developing dishes could be placed, and the whole brought out
into the daylight and suitably rocked. In this way ten or twelve
photographs could be developed simultaneously.
It may be worth while to mention here that the bright spark given by
breaking the _primary_ circuit of an induction coil at the surface of
mercury was found to be of much too long duration to be useful for the
purposes of splash-photography.
FOOTNOTES:
[C] The plates which I have mostly used have been Thomas's A 1
ordinary.
CHAPTER II
THE SPLASH OF A DROP--LOW FALL
We will now turn to the photographic record itself. The first series
shows the splash of a drop of water weighing ·2 of a gram, and therefore
7·36 millimetres (or rather less than one-third of an inch) in diameter,
falling 40 cm. (about 16 inches) into milk mixed with water. The object
of adding milk to the water was to make it more visible. The addition of
milk makes, as we shall see, a little but not much difference in the
general character of the splash. The scale of the figures is
three-quarters of the actual size.
The number written against any figure gives, on the assumption that no
unobserved error has crept in, the time in decimal parts of a second
that has elapsed since the stage marked "_T = 0_," which is nearest to
the first instant of contact. The reader will understand from what has
been said that the error in any of these times may be as much as
two-thousandths of a second, but is not likely to be more than that,
when all precautions were taken.
It will be observed that as the drop descends into the liquid the upper
portion is at first not appreciably distorted, but that a little cup or
crater of liquid is thrown up round it. As the drop descends further,
this crater grows wider and higher and thicker in the wall, and jets are
shot out from its edge or rim. These jets are visible even in the second
figure. The black marks on the inside wall of the crater are due to the
lamp-black carried down with the drop from the smoked surface of the
supporting cup: though in one sense a disfigurement, they serve to show
by their presence that the interior of the crater _is lined by the
original liquid which formed the drop_, and thus afford useful
information as to the nature of the flow.
The crater rises with great rapidity up to Fig. 4. In Fig. 5 the walls
are beginning to grow thicker, while the next three figures show the
crater subsiding and widening, till in Fig. 9 it lies as a mere ring of
lobes on the surface, surrounding a central hollow.
[Illustration: SERIES I
Milk into water (40 cm.). Scale 3/4.
1
2 T = 0
3 0·002 sec.
4 0·007 sec.
5 0·018 sec.
6 0·031 sec.
7 0·040 sec.
8 0·050 sec.
9 0·056 sec.]
Fig. 10 shows the beginning of the rebound, in the rising of a central
column. It will be seen that the lamp-black is now all swept to the
middle, indicating that _the liquid of the original drop emerges at the
head_ of the central column. Full confirmation of this is obtained from
Fig. 12, which represents the emergent column obtained when the
circumstances are all the same, except that we have a drop of milk
falling into water instead of water falling into milk. It will be
observed that the upper part only of the column is visible, precisely
because it contains nearly all the milk of the drop, while the lower
part, consisting chiefly of transparent water, remains invisible.
[Illustration: SERIES I--(_continued_)
10 0·064 sec.
11 0·073 sec.
12
13 0·093 sec.]
No. 15 shows the column at its greatest height, and it should be noticed
that Figs. 16 and 17 show a tendency on the part of the head of this
column to split off as a separate drop.
[Illustration: SERIES I--(_continued_)
14 0·103 sec.
15 0·116 sec.
16 0·129 sec.]
The column in subsiding forms a "cake" of liquid round the base. The
edge of this circular cake (see Figs. 17, 18, and 19) is the first
well-marked ripple spreading outwards in an ever-widening circle.
[Illustration: SERIES I--(_continued_)
17 0·153 sec.
18 0·197 sec.
19 0·217 sec.]
If Fig. 19 is reached without the top of the column having separated,
then the splash follows the course shown in Figs. 20-a to 23-a, in which
it will be observed that the disappearance of the first column is very
quickly followed by the rise of a secondary column very different in
shape, which itself subsides again, but has not yet (in 23-a) formed, as
it ultimately will, a second "cake" on the top of the first. Thus the
second ripple follows late after the first.
[Illustration: SERIES I--(_continued_)
Alternative (_a_).
20-a 0·240 sec.
21-a 0·242 sec.
22-a 0·248 sec.
23-a 0·253 sec.]
If, however, the summit of the primary column succeeds in breaking off
(as in Fig. 18-b), or even in very nearly breaking off, then the impact
of this newly-formed drop forms a second slight crater on the top of the
first cake, and we have the series (18-b to 24-b), in which it will be
observed that the rim of the secondary crater spreads rapidly outwards,
so that a second well-marked circular ripple in this case _quickly_
follows the first. The secondary column that is thrown up in Fig. 23-b
is very like that which emerged at a much earlier stage in the (_a_)
series.
The photographs of this (_b_) series show very beautifully the manner in
which the advancing edge of the ripple degenerates into smaller ripples
travelling with greater speed.
[Illustration: SERIES I--(_continued_)
Alternative (_b_).
18-b 0·214 sec.
19-b 0·237 sec.
20-b 0·242 sec.
21-b 0·244 sec.]
[Illustration: SERIES I--(_continued_)
Alternative (_b_).
22-b 0·261 sec.
23-b 0·257 sec.
24-b 0·311 sec.]
It will be readily understood that if the splitting off of the head of
the primary column happens to take place a little earlier, or on the
other hand is nearly, but not quite, complete when it descends below the
surface, then subsequent configurations will differ somewhat from either
of the sub-series here shown.
Since any figure photographed might belong to either sequence, the
disentanglement of the two series required careful consideration and
long experimenting.
The reappearance of the original drop at the head of the rebounding
column, of which the explanation has been given in this chapter, is
easily verified by naked-eye observation.
Let the reader when he next receives a cup of tea or coffee to which no
milk has yet been added, make the simple experiment of dropping into it
from a spoon, at the height of fifteen or sixteen inches above the
surface, a single drop of milk. He will have no difficulty in
recognizing that the column which emerges carries the white milk-drop at
the top only slightly stained by the liquid into which it has fallen.
In the same way naked-eye observation reveals the crater thrown up by
the entry of a big rain-drop into a pool of water. In either case what
we are able to glimpse is a "stationary" stage. The rebounding column
reaches a maximum height, remains poised for an instant, and then
descends. The same is true of the crater. It is the relatively long
duration of the moment of poise that produces on the eye a clear
impression where all else is blurred by rapid change.
But there is frequently a curious illusion. We often seem to see the
crater with the column standing erect in the middle of it. We know now
that in reality the crater has vanished before the column appears. But
the image of the crater has not time to fade before that of the column
is superposed on it.
Those who are accustomed "to believe nothing that they hear and only
half of what they see" may be glad to find at least the latter part of
their maxim so completely justified.
CHAPTER III
PRINCIPLES INVOLVED
The reader's attention has now been directed to various features which,
with certain modifications, will be found in many of the splashes that
we shall examine; but so far the language used has been simply
descriptive and in no way explanatory. Instead of going on to describe
other splashes in the same way, and thus to accumulate a great mass of
uncoördinated descriptive detail, it will be better to pause for a
moment in order to become acquainted with certain principles connected
with the behaviour of liquids, the application of which will go a long
way towards explaining what we see going on in any splash.
The first principle to be understood is that the surface layers of
any liquid behave like a uniformly stretched skin or membrane, which
is always endeavouring to contract and to diminish its area. If the
surface is flat, like the surface of still liquid in a bowl, this
surface-tension has only the effect of exerting a small inward pull on
the walls of the bowl. But if the surface is curved, with a convexity
outwards, then the surface layers, on account of their tension, press
the interior liquid back, and thus tend to check the growth of any
protuberance; while, on the other hand, if the surface is concave
outwards, then the surface-tension tends to pull the interior liquid
forward, and so to diminish the concavity.
Direct evidence of this surface-tension is easy to cite. We have it in
any pendent drop, such as any of those shown in the accompanying
figures.
[Illustration: WATER.
TURPENTINE.
Pendent drops (magnified 2-1/4 times).]
If we ask ourselves how it is that the liquid in the interior of one of
these drops does not flow out, pressed as it is by the liquid above it,
the answer is that everywhere the stretched skin presses it back. A
soap-bubble too presses on the air in its interior, both the outside
layers and the inside layers of the thin film being curved over the
interior space. This is the reason that a soap-bubble blown on the bowl
of a pipe will slowly collapse again if we remove the stem of the pipe
from our mouth. The bubble drives the interior air back through the
pipe. And it is easy to show that if two soap-bubbles be blown on the
ends of two tubes which can be connected together by opening a tap
between them, then the smaller will collapse and blow out the larger.
The reason of this is that in the bubble of smaller radius the surface
layers are more sharply curved, and therefore exert a greater pressure
on the air within. Thus if a strap be pulled at each end with a total
tension T and bent over a solid cylinder of small radius, as in Fig. 6,
it is easy to see that the pressure on the surface of the part of the
cylinder touched by the strap is less than if the strap be bent over an
equal area on a cylinder of larger radius (Fig. 7). The tension of the
surface layers of a liquid causes them to act on the liquid within,
exactly as does the stretched strap on the solid in these figures. If at
any place the liquid presents, as it generally does, not a cylindrical
surface, but one with curvature in two directions, then the pressure
corresponds to what would be produced by two straps crossing at right
angles, laid one over the other, each with the curvature of the surface
in its direction (Fig. 8).
[Illustration: FIG. 6]
[Illustration: FIG. 7]
[Illustration: FIG. 8]
[Illustration: FIG. 9]
We can now understand why the drop that has been lying on the
watch-glass should oscillate in its descent. The sharp curvature of the
edge AA of the drop (see Fig. 9) tells us that the liquid there is
pushed back by the pressure of the stretched surface layers, and when
the supporting glass is removed the sides of the drop move inwards,
driving the liquid into the lower part, the tendency being to make the
drop spherical, and so to equalize the pressure of the surface at all
points. But in the process the liquid overshoots the mark, and the drop
becomes elongated vertically and flattened at the sides. This causes the
curvature at top and bottom to be sharper than at the sides, and on this
account the back-pressure of the ends soon checks the elongation and
finally reverses the flow of liquid, and the drop flattens again. As an
example of the way in which a _concavity_ of the surface is pulled out
by the surface-tension may be cited the dimples made by the weight of an
aquatic insect, where its feet rest on the surface without penetrating
it.
This same surface-tension checks the rise of the crater, and would cause
it to subside again even without the action of gravity. Thus the
pressures of the sharply curved crater-edge on the liquid between the
crater walls are indicated by the dotted arrows in Fig. 10, and arise
from the surface-tension indicated by the full arrows. During the early
part of the splash the surface-tension is more important than gravity in
checking the rise of the walls. For, as the numbers show, the crater of
Series I is already at about its maximum height in No. 4, i.e. about
seven-thousandths of a second after first contact. In this time the fall
due to gravity would be only about 1/100 of an inch. Thus if gravity had
not acted the crater would only have risen about 1/100 of an inch
higher. The same reasoning applies to the rise of the central column,
but here the curvature at the summit is much less sharp. The numbers
show that the column reaches its maximum height in about 5/100 of a
second after its start in No. 10, and in this time the fall due to
gravity is about half an inch, so that gravity has reduced the height by
this amount.
[Illustration: FIG. 10]
The second principle which I will now mention enables us to explain the
occurrence of the jets and rays at the edge of the crater and their
splitting into drops.
It was shown in 1873 by the blind Belgian philosopher, Plateau,[D] that
a cylinder of liquid is not a figure of stable equilibrium if its length
exceeds about 3-1/7 times its diameter. Thus a long cylindrical rod of
liquid, such as Fig. 11, if it could be obtained and left for a moment
to itself, would at once topple into a row of sensibly equal,
equidistant drops, the number of which is expressed by a very simple
law, viz. that for every 3-1/7 times the diameter there is a drop, or
that the distance between the centres of the drops is equal to the
circumference of the cylinder.
[Illustration: FIG. 11]
The cause of this instability is the action of the same skin-tension
that we have already spoken of. Calculation shows, and Plateau was able
to confirm the calculation by experiment, that if through chance
agitations lobes are formed at a nearer distance apart than 3-1/7 times
the radius, with hollows between as in the accompanying Fig. 12, then
the curvatures will be such as to make the skin-tension push the
protuberances back and pull the hollows out. But if the protuberances
occur at any greater distances apart than the length of the perimeter,
then the sharper curvature of the narrower parts will drive the liquid
there into the parts already wider, thus any such an initial accidental
inequality of diameter will go on increasing, or the whole will topple
into drops.
[Illustration: FIG. 12]
At the last moment the drops are joined by narrow necks of liquid (Fig.
13), which themselves split up into secondary droplets (Fig. 14).
[Illustration: FIG. 13]
[Illustration: FIG. 14]
What we have said of a straight liquid cylinder applies also to an
annulus of liquid made by bending such a cylinder into a ring. This also
will spontaneously segment or topple into drops according to the same
law.[E] Now the edge of the crater is practically such a ring, and it
topples into a more or less regular set of protuberances, the liquid
being driven from the parts between into the protuberances.
Now while the crater is rising the liquid is flowing up from below
towards the rim, and the spontaneous segmentation of the rim means that
channels of easier flow are created, whereby the liquid is driven into
the protuberances, which thus become a series of jets. These are the
jets or arms which we see at the edge of the crater. Examination with a
lens of some of the craters will show that the lines of easier flow
leading to a jet are often marked by streaks of lamp-black in Series I,
or by streaks of milk in Series II. This explanation of the formation of
the jets applies also to a similar phenomenon on a much larger scale,
with which the reader will be already familiar. If he has ever watched
on a still day, on a straight, slightly shelving sandy shore, the waves
that have just impetus enough to curl over and break, he will have
noticed that up to a certain moment the wave presents a long, smooth,
horizontal cylindrical edge (see Fig. 15-a) from which, at a given
instant, are shot out an immense array of little jets which speedily
break into foam, and at the same moment the back of the wave, hitherto
smooth, is seen to be furrowed or combed (see Fig. 15-b). The jets are
due to the segmentation of the cylindrical rim according to Plateau's
law, and the ridges between the furrows mark the lines of easier flow
determined by the position of the jets.
[Illustration: FIG. 15-b
FIG. 15-a
Diagrams of a breaking wave.]
The tendency of the central column of Series I to separate into two
parts is only another illustration of the same instability of a liquid
cylinder. The column, however, is much thicker than the jets, and its
surface is therefore less sharply curved, and consequently the inward
pressure of the stretched curved surface is relatively slight and the
segmentation proceeds only slowly. Since this segmentation must
originate in some accidental tremor, we see how it is that the summit
of the column may succeed in separating off on some occasions and not on
others. As a matter of fact, the height of fall for this particular
splash was purposely selected, so that the column thrown up should
_just_ not succeed in dividing in order that the formation of the
subsequent ripples might not be disturbed by the falling in of the drops
split off. But, as the reader will have perceived, the margin allowed
was not quite sufficient.
The two principles that I have now explained, viz. the principle of the
skin-tension, and the principle of the instability and spontaneous
segmentation of a liquid cylinder, jet, or annulus, will go far to
explain much that we shall see in any splash, but it is well that the
reader should realize how much has been left unexplained. Why, for
example, should the crater rise so suddenly and vertically immediately
round the drop as it enters? Why should the drop spread itself out as a
lining over the inside of the crater, turning itself inside out, as it
were, and making an inverted umbrella of itself? Why when the crater
subsides should it flow inwards rather than outwards, so as to throw up
such a remarkable central column?
These questions, which demand that we should trace the motion of every
particle of the water back to the original impulse given by the impact
of the drop, are much more difficult to answer, and can only be
satisfactorily dealt with by a complicated mathematical analysis.
Something, however, in the way of a general explanation will be given in
a later chapter.
FOOTNOTES:
[D] _Statique Expérimentale et Théorique des Liquides._
[E] See Worthington on the "Segmentation of a Liquid Annulus," _Proc.
Roy. Soc._, No. 200, 1879.
CHAPTER IV
THE SPLASH CONTINUED
I have stated that the addition of the milk to the water made but little
difference in the character of the resulting splash. It does, however,
make certain differences in detail, as will be gathered from an
examination of the next Series I-a, which shows the effect of letting
the water-drop fall from the same height into water instead of into
milk. Such a splash is difficult to photograph unless the illumination
is from behind. As shown in this way, the early figures of the crater
might be unintelligible to the reader had he not already studied the
same crater lighted up from the side. Sometimes, though the front of the
crater is hardly visible directly, yet every lobe on it can be clearly
traced in the inverted image seen by reflection.
The most noticeable difference between the two splashes is perhaps the
very much greater number of ripples seen with the splash in pure water.
This is partly because, with the illumination behind, such ripples are
more easily visible, but arises chiefly from the fact that ripples are
not so readily propagated over the surface of milk on account both of
its smaller surface-tension and its greater viscosity. The first
appearance of outward-spreading ripples is in No. 6, just round the
subsiding crater.
[Illustration: SERIES I-a
Water into water (40 cm. fall). Scale 9/10.
1 T = 0
2 0·004 sec.
3 0·013 sec.
4 0·018 sec.]
[Illustration: SERIES I-a--(_continued_)
5 0·026 sec.
6 0·042 sec.
7 0·058 sec.
8 0·073 sec.]
Since the origination of these ripples is an interesting phenomenon from
a physical point of view, as throwing light on the dispersion of waves
travelling with different velocities, special precautions were taken to
secure the most favourable conditions, and in order to clean the surface
after the arrival of each drop, which inevitably brings down a little
adherent lamp-black, a continuous slow stream of fresh water was
maintained which swept the contaminated surface-liquid away over the
edge of the vessel.
The effect of this precaution is seen by a comparison of the photographs
No. 11 and No. 11-a. In the first the surface was kept quite clean in
the way described; in the second it had only been cleaned by skimming it
with a fine wire-gauze dish.
The beginning of the descent of the first central column seems to be
marked by the appearance of a slight depression round its base, which
has just not begun in No. 11-a, and has just begun in No. 11, and goes
on increasing in Figs. 12 and 13.
[Illustration: SERIES I-a--(_continued_)
Running water. Scale reduced to 6/10.
9 0·087 sec.
10 0·014 sec.
11 0·139 sec.
11-a 0·139 sec.]
[Illustration: SERIES I-a--(_continued_)
Running water. Scale 6/10.
12 0·163 sec.
13 0·185 sec.
14 0·207 sec.
15 0·227 sec.]
The same feature marks the beginning of the descent of the secondary
central column, which is still rising in Fig. 17, is just poised in Fig.
18, and thence onwards shows a gradually increasing central depression.
These last four figures carry us to a rather later stage than was
reached in Series I.
It should be noticed that in this Series the water-drop used was of
smaller diameter than that of Series I, weighing ·13 grams as against ·2
grams. By employing the smaller drop, we diminish irregularities due to
oscillations of form set up on release, for the smaller drop is more
spherical when lying on the dropping cup than the larger; a few
photographs taken for comparison with the full-sized drop showed,
however, extremely little difference in the splashes at this height of
fall.
[Illustration: SERIES I-a--(_continued_)
Still water. Scale 9/10.
16 0·247 sec.
17 0·266 sec.
18 0·294 sec.]
[Illustration: SERIES I-a--(_continued_)
Still water. Scale 9/10.
19 0·285 sec.
20 0·311 sec.
21 0·321 sec.]
CHAPTER V
HIGHER FALLS--BUBBLE-BUILDING
It might well be expected that the effect of increasing the height of
fall of our drop to 100 cm. would be simply to emphasize the phenomena
already observed, and to obtain a higher crater and a taller rebounding
column. Such an expectation would be mistaken. A new phenomenon makes
its appearance. The crater does indeed rise to a greater height, but its
mouth closes so as to form a bubble on the surface of the liquid. If the
height be not too great the closing is either incomplete or at any rate
only temporary, and the bubble reopens at the top to make way for the
column which rises as before from the base, but is now much thicker and
hardly so high as before.
In the Series II, which is now given, the drop was of milk, 7·36 mm. in
diameter, and fell 100 cm. into water.
Photographs 1 and 2--to which is added 2-a, though taken under slightly
different conditions--show that the drop on entering punches a
sheer-walled hole, for the fine line of light seen above the level of
the top of the drop in Figs. 2 and 2-a marks the circular cliff-like
edge of the as yet undisturbed liquid. Up the vertical sides of this
circular pit the liquid of the drop is streaming. This cliff is highest
and perhaps clearest in Fig. 2-a.
The closing of the mouth of the crater, which is just beginning in Fig.
5, is to be explained as follows. If the crater were a simple
thin-walled cylinder of liquid, it would contract under the influence of
the surface-tension just as does a soap-bubble, but not so fast, since
the walls have only a horizontal curvature. If the wall is thinner above
than below, then the upper part will contract faster than the lower,
through there being less liquid to accelerate. Now the supply of liquid
is from below, and will thicken the lower part of the walls first, and
thus account for the faster closing of the mouth. On the other hand, the
uppermost edge of the crater is the place where the checking influence
of the surface-tension on the upward flow is first felt, with the result
that the edge of the rim is thickened by the influx from below, so that
a more or less regular rope-like annulus is formed round the edge. Now
calculation shows that such an annulus, so long as its thickness is not
more than 1·61 times the thickness of the wall below, will contract
quicker than the wall, and this will tend to close the crater, somewhat
as a bag would be closed by the contraction of an elastic cord round the
mouth. This rope-like thickening of the edge is to be seen in Figs. 5
and 7, and especially in Figs. 3 and 4 of Series III on page 63.
[Illustration: SERIES II
Milk into water (100 cm. fall).
1 0·002 sec.
2-a
2 0·002 sec.
3 0·002 sec.
4 0·009 sec.
5 0·018 sec.
6 0·018 sec.
7 0·039 sec.]
The photographs 9, 10, and 11 (obtained after adding a little milk to
the water in order to render it more visible) were at first very
puzzling. What happens is that the bubble sometimes reopens very soon
(or perhaps does not quite close) as in Fig. 9, and makes way for the
column which rises from the base exactly as in the previous series. This
column may be dimly seen through the walls of the bubble in Fig. 9, and
No. 10 shows the column alone, the bubble having opened early and
receded with great velocity, a few drops round the base being all that
is left of it. Nos. 10-a and 10-b illustrate this reopening. In 10-a the
milk-drop was allowed to fall again into quite pure water, and the
photograph shows very beautifully the summit of the column, with the
original milk-drop at the top, emerging through the reopening mouth of
the bubble; and Fig. 10-b shows the same at a very slightly later stage
when the bubble has completely retreated.
[Illustration: SERIES II--(_continued_)
8 0·054 sec.
9 0·085 sec.
10 0·105 sec.
10-a 0·103 sec.
10-b 0·111 sec.]
In Fig. 11 the bubble has been too firmly closed to reopen, and the
summit has been struck by the column within. The next figure (No. 12)
shows how in such a case the emergent column becomes entangled in the
liquid of the bubble when it bursts. Under the influence, however, of
the surface-tension, which pushes back the protuberances and pulls out
the hollows, regularity of form is soon regained. Thus Fig. 13 shows the
emergent columns at a later stage after such an encounter, already much
more symmetrical; and the subsequent photographs (for which a good deal
of milk was added for the sake of greater visibility) show a column of
uniformly sedate and respectable rotundity, betraying no traces of any
youthful irregularities.
[Illustration: SERIES II--(_continued_)
11 0·105 sec.
12 0·095 sec.
13 0·113 sec.
14 0·132 sec.
15 0·194 sec.]
[Illustration: SERIES II--(_continued_)
16 0·217 sec.
17 0·240 sec.
18 0·272 sec.
19 0·311 sec.]
Series III shows the effect of still further increasing the height of
fall of the water-drop (to 137 cm., or about 4 ft. 6 in.), and at the
same time doubling its volume so that it now weighs ·4 gram. The crater
now closes in about 18/1000 of a second, and forms a comparatively
permanent bubble. The rope-like thickening of the edge, already alluded
to, is well seen in Figs. 3 and 4. In its earlier stages the bubble is
thick-walled, rough, and furrowed, but becomes smoother and thinner the
longer it lasts, both because the liquid drains down the sides and
because it becomes more uniformly distributed under the equalizing
influence of the surface-tension.
[Illustration: SERIES III
Water-drop weighing 0·4 grams falling 137 cm. (4-1/2 feet) into milk
mixed with water. Scale 1/2.
1 T = 0
2 0·005 sec.
3 0·016 sec.
4 0·019 sec.]
Such a bubble may remain long closed, as in Fig. 8, becoming every
moment more delicate and exquisite, or it may open at an even earlier
stage, as in Fig. 9.
There is a characteristic difference between the arms of a closing and
of an opening bubble. It will be noticed that up to the moment of
closing the arms slope outwards. The upper portions have been projected
at an earlier stage when the mouth of the crater was wider open and the
flow was either actually outwards or more nearly vertical; then as the
mouth contracts the arms are left behind in the upper parts.
[Illustration: SERIES III--(_continued_)
5 0·017 sec.
6 0·020 sec.
7 0·036 sec.
8 0·053 sec.]
In an opening bubble, on the other hand, the arms are at first vertical,
and later have the very characteristic inward slope of the last figure,
which is also well seen in Fig. 10-a of the last series. Here the edge
of the opened bubble retreats outwards and downwards, leaving the arms
behind.
Such is the origin of the bubbles raised by the big drops of a thunder
shower on the surface of a pool. The building of each fairy dome is
accomplished in less than two-hundredths of a second, and before
one-tenth of a second has elapsed the whole construction may have
vanished. One can almost regret that so beautiful a process should have
been so long unwatched.
To build these bubbles a large drop is essential. With a drop weighing
only 0·4 of a gram, even though it fall from a height of 177 cm., there
is no bubble, and the splash is almost exactly that of Series I-a. The
exact time required for the closing of the bubble probably depends a
good deal on the phase of oscillation of the drop at the moment of
entry, and, as already observed, a big drop, which lies very flat in
the dropping cup, is set vibrating more strongly on liberation than a
small one.
We shall see in Chapter VII that the impact of a rough solid sphere, if
falling from a sufficient height, produces a very exquisite bubble; in
this case irregularities due to oscillation are absent, and the closing
can be timed with greater precision.
[Illustration: SERIES III--(_continued_)
9 0·040 sec.
10 0·046 sec.
11 0·070 sec.]
[Illustration: FIG. 16
Arrangement for taking photographs below the surface of the liquid.]
CHAPTER VI
BELOW THE SURFACE[F]
Our investigation has so far been limited to what we can see from above
the surface of the liquid; nor perhaps would it occur to any one
acquainted only with so much as we have yet examined that it might be
worth while to look below the general level of the surface. The
discovery, however, that when the splash is made by a solid sphere very
remarkable phenomena, which will be described in the next chapter, take
place below the surface, led at a much later date to a similar
examination in the case of a liquid drop.
A suitable arrangement of the apparatus in the dark room is shown in the
accompanying diagram (Fig. 16).
The water into which the drop is to fall is placed in a thin glass
vessel AB, with parallel sides. (An inverted clock-shade makes a very
convenient vessel.) The water fills the vessel to the brim, and is
allowed to overflow it in a steady stream, thus presenting a surface
which, being perpetually renewed, is maintained perfectly clean. Close
behind the vessel is a plate P of finely roughened glass, on which the
light from the spark-gap F, in front of its concave reflector M, is
thrown by means of the condenser lens L taken from an optical lantern.
This provides a very uniformly illuminated background against which the
splash is viewed by means of the camera C, whose optic axis is
horizontal, either a little below the level of the liquid surface or at
that level. By having it just at the level of the surface we secure
simultaneous pictures of what is going on both above and below the
surface. There is, to be sure, a narrow band or region of confusion
stretching across the photographs in which the images obtained by
reflection, both external and internal, overlap the direct images, and
it should also be mentioned that the two pictures will not be quite in
focus together, for the optical effect of the water, through which the
part below the surface is viewed, is to bring the image forward.
The photographs of Series IV were obtained in this way from the splash
of a drop of water weighing 0·176 grams falling 40 cm. into water. (The
same splash as that of Series I-a.) The perfectly spherical form
presented by the cavity below the surface is very remarkable. In the
present case, this spherical cavity when at its deepest, as in Fig. 5,
would contain about fifty of the original drops, and in other
cases--e.g. with a drop of 1/4 the volume, falling from 177 cm.--the
cavity would contain as many as 360 of the original drops.
In Figs. 5, 6, and 7 the depth of the cavity is nearly constant, but the
diameter is steadily increasing. The spherical form, however, is still
maintained. The last figure shows the central column just beginning to
rise.
[Illustration: SERIES IV
The splash of Series I-a viewed below the surface.
1
2 T = 0
3 0·009 sec.
4 0·012 sec.
5 0·016 sec.
6 0·023 sec.
7 0·039 sec.
8 0·055 sec.
9 0·070 sec.]
There can be no doubt that the liquid of the original drop is spread out
in an excessively thin lining over the interior of this sphere. The
reader has seen for himself part of the evidence in the streaks of milk
that are carried up the inner walls of the crater when a milk-drop falls
into water (Series II); in the streaks of lamp-black that are carried
there when the drop is of milk, and it may here be mentioned that other
photographs that cannot be reproduced here have enabled me to trace the
gradual deformation of the drop into this thin layer and show that it
passes through configurations like Figs. 17, 18, and 19.
[Illustration: FIG. 17]
[Illustration: FIG. 18]
[Illustration: FIG. 19]
It appears possible that the study of this remarkable spherical
excavation may afford a clue that will lead to a solution of the very
difficult hydro-dynamical questions involved, and the matter is still
being investigated.
FOOTNOTES:
[F] The information conveyed in this chapter was first published in a
communication to the Mathematical and Physical Section of the British
Association at Leicester in 1907.
CHAPTER VII
THE TWO KINDS OF SPLASHES OF SOLID SPHERES
In the present chapter will be described the splash that follows the
entry of a _solid_ sphere falling vertically into a liquid from a small
height, and I should like to persuade the reader, if possible before he
begins to read, or at any rate afterwards, to make a very simple
experiment. Let a few child's marbles be taken--not glass "marbles," for
these are seldom round enough or smooth enough, but what are sold in the
toy-shops as "stone" marbles--and let one of these be well rubbed and
polished with a dry handkerchief, and then dropped from a height of
about 30 cm., or, say, 1 foot, into a deep bowl or basin of water, the
bottom of which may be conveniently protected from breakage by a few
folds of fine copper gauze.
If the polishing has been good, and the surface of the sphere has not
been dimmed by subsequent handling with hot or greasy fingers, it will
be observed that the splash is singularly insignificant, the sphere
slipping noiselessly into the liquid with very little disturbance of the
surface.
But if the same sphere be fished out of the water, and again let fall
from the same height without being first dried, or, better still, if
another marble be taken, which has been previously roughened with
sand-paper, the resulting splash is totally different. There is now a
noise of bubbles, which may be seen rising through the liquid, and a
tall jet is seen to be tossed into the air.
(1) THE SPLASH OF A ROUGH SPHERE.
To understand the cause of this really surprising difference we must
turn to the photographic record, and we will take first the case of a
rough sphere falling into water to which milk has been added for the
sake of clearness in the photographs. The diameter of the sphere was 1·5
cm. (or 3/5 inch), and the height of fall 15 cm., or just about 6
inches. The sphere on each occasion was fished out, redried, and
re-roughened with sand- or emery-paper. Examination of the first
photographs of Series V shows that the liquid, instead of flowing over
and wetting the surface of the sphere, is driven violently away, so that
as far as can be seen from above the upper portion is, at first at any
rate, unwetted by the liquid. The crater that is subsequently formed is
very similar to that which was thrown by the liquid drop in Series I,
the main difference being that in the present-case the crater is thinner
in the wall and more regular. This greater regularity is chiefly to be
attributed to the fact that the solid sphere enters the liquid with a
true spherical form, and is not distorted by the oscillations and
tremors which disturb a falling drop. The gradual thickening of the wall
and the corresponding reduction in the number of lobes as the subsidence
proceeds is beautifully shown in Figs. 7, 8, 9, and 10, the
last-mentioned figure being hardly distinguishable from the
corresponding Fig. 9 of Series I, p. 17. This stage is in each case
reached in about 58/1000 of a second.
[Illustration: SERIES V
Rough sphere. "Basket splash."
Diameter of sphere, 1·5 centim. Height of fall, 15 centim.
1 T = 0
2 0·003 sec.
3 0·006 sec.
4
5
6]
[Illustration: SERIES V
Rough sphere--(_continued_).
7 0·024 sec.
8 0·032 sec.
9 0·042 sec.
10 0·060 sec.]
Now from the depths of the crater there rises with surprising velocity
the exquisite jet of Fig. 11, which in obedience to the law of
segmentation at once splits up in its upper portion into little drops,
while at the same time it gathers volume from below, and rises
ultimately as a tall, graceful column to a height which may be even
greater than that from which the sphere fell. This is the emergent jet
which one sees with the naked eye whenever a sufficiently rough sphere
is dropped from a small height into water, but if we are to ascertain
how this column originates, we must follow the sphere below the surface
of the liquid. The arrangement already described on p. 69 enables this
to be done. We let the sphere fall into clear water contained in a
narrow, flat-sided, inverted clock-shade and illuminate this from behind
while the camera stands straight in front.
[Illustration: SERIES V
Rough sphere--(_continued_).
11 0·068 sec.
12 0·076 sec.
13 0·088 sec.
14 0·100 sec.]
In this manner were obtained the photographs of Series VI, which require
a little explanation. In the first figure we see the sphere just
entering the liquid. The faint horizontal line shows the level of the
surface. Above this line we see the internally reflected image of the
part that has already entered, while still higher in the figure may be
discerned the summit of the sphere itself. The slight lateral
displacement of the part below the surface is due to refraction
consequent on the camera having been set with its optic axis not quite
perpendicular to the face of the vessel. In the subsequent figures it
will be observed that the sphere, as it descends, drags with it the
surface of the liquid in the form of a gradually deepening pocket or
bag, the upper part of the sphere being for a long time quite unwetted
by the liquid.
The sides of this pocket or bag of air not being quite smooth, give a
somewhat distorted appearance to the sphere within. Also, since the
sides are sloping, their reflected image in the level surface slopes in
the opposite direction and produces an angle where the two meet. This
angle marks very clearly the level of the surface. Above the
surface-line in Figs. 2 to 5 is seen the beaded lip of the crater which
we have already viewed from above, but this is somewhat out of focus,
for the camera had to be focused on the sphere as seen under water, and
the effect of the water is to bring the sphere optically nearer. Hence
only the nearer part of the crater, i.e. the middle part of the front
edge, is distinctly shown.
[Illustration: SERIES VI
The splash of a rough sphere as seen below the surface.
Diameter, 1·5 centim. Height of fall, 15 centim.
1 T = 0
2 0·010 sec.
3 0·018 sec.
4 0·023 sec.
5 0·032 sec.]
Coming now to Fig. 6, we perceive that the long cylindrical hollow has
begun to divide. In this spontaneous division we have another
illustration of the law of instability which regulated the sub-division
of the jets and columns of earlier series. This law is the same whether
the cylinder be of air surrounded by liquid or of liquid surrounded by
air. Hitherto we have only seen it operating in jets of liquid in air;
now we have a jet of air in a liquid.
The lower part of the long cylinder of air splits off into a bubble just
behind the sphere, and follows in its wake to the bottom of the vessel,
and is only detached and rises to the surface when the sphere strikes
the bottom. Many years ago, through the kindness of the curator of the
Brighton Aquarium, I was enabled to watch this bubble of air following
in the wake of the sphere to the bottom of the deepest tank.
Figs. 7, 8, and 9 show the two parts gradually separating.
[Illustration: SERIES VI--(_continued_)
Scale reduced to about 7/10.
6 0·045 sec.
7
8 0·050 sec.
9 0·054 sec.]
Fig. 10 shows specially well the ripples on the surface of the
descending bubble. These undulations sometimes become so accentuated
that the upper part of this descending bubble is detached, and then the
curious phenomenon may be seen of this detached part still following the
rest downwards through the liquid with an unsteady, lurching motion.
Meanwhile the upper half of the divided air-column is seen in Fig. 9 to
resemble a deep basin which now rapidly fills up by the influx of liquid
from all sides. It is from the confluence of this inflowing liquid into
channels which necessarily narrow as the centre is approached that the
great velocity with which the liquid spirts upwards is obtained. In Fig.
11 the jet is just discernible above the surface, and in Fig. 13 it is
well-established.
[Illustration: SERIES VI--(_continued_)
10 0·062 sec.
11
12 0·062 sec.
13 0·070 sec.]
On increasing the height of fall of a rough sphere to 60 cm., we obtain
a higher crater which closes and forms a bubble, exactly as when we
increased the height of fall of a liquid drop. The process as viewed
from above the surface is shown in Series VII. The first figure of this
series shows very well how completely the liquid is driven away from the
surface of the sphere the first moment of contact. The subsequent crater
and bubble are of exquisite delicacy. This bubble, though it closes
completely as in the last figure, is doomed to almost immediate
destruction. For we see, on looking below the surface, that the
proceedings there are of the same kind as in the case of the lower fall
already described, and result in the formation of an upward-directed
jet.
[Illustration: SERIES VII
Rough sphere falling 60 cm. Scale 3/4.
1 T = 0
2 0·003 sec.
3 0·017 sec.
4 0·017 sec.
5 0·033 sec.]
Thus the first three figures of Series VIII show the last moments of a
bubble which has burst, spontaneously, and so has made way for the jet
of Fig. 3. (These are taken from a splash into petroleum with 24·5 cm.
fall.) But the last two figures, 4 and 5 (taken with a 32 cm. fall),
show how a bubble which might otherwise have been permanent, is stabbed
by the rising jet and destroyed. With water and 60 cm. fall the jet
appears sometimes to rise quite unimpeded, and sometimes to be checked
by the still closed bubble.
Before leaving the splash of a rough sphere, I desire to call the
reader's attention to another point.
Such figures as 7, 9, and 10 of Series V, p. 77, show that the surface
of the liquid beyond the walls of the crater is still flat and
undisturbed; yet we now know from the corresponding Figs. 5, 6, and 7 of
Series VI, p. 83, that a large volume of liquid has been displaced, much
larger than the quantity required to form the crater wall. The inference
is that the level of the surface has been slightly raised even at a
great distance from the place of the splash. Figs. 7, 8, and 9 of Series
VI themselves confirm the impression of the undisturbed flatness of the
surface at even a small distance from the splash.
(2) THE SPLASH OF A SMOOTH SPHERE.
The reader who has been sufficiently interested to make for himself the
simple experiment suggested at the beginning of this chapter, will have
already realized that the splash of a smooth sphere is totally different
from that of a rough one. The photographs of Series IX show that the
difference is quite pronounced from the first instant of contact. In
this series the sphere was of polished stone 3·2 cm. in diameter and
fell 14 cm. The scale of magnification is 3/4. The second figure shows
that the liquid, instead of being driven away from the surface as was
the case with a rough sphere, now rises up in a thin, closely-fitting
sheath which (see Fig. 3) completely envelops the sphere even before its
summit has reached the water-level. Figs. 4 and 5 show the comparatively
insignificant column that remains to mark the spot where the sphere has
entered. Fig. 6 was the result of a lucky accident, which left the
sphere rough on the right-hand side, smooth on the left. Nothing could
show better than this photograph the essential difference between the
two splashes.
[Illustration: SERIES VIII
Rough sphere. Splashes viewed below the surface.
The bursting of the bubble.
1 0·055 sec.
From a splash into Petroleum
24·5 cm. fall.
2 0·060 sec.
3 0·064 sec.
From a splash into Petroleum
32 cm. fall.
4 0·070 sec.
5 0·082 sec.]
The reader's attention is directed to the remarkably deep furrows which
characterize the whole sheath in Fig. 3 and the left-hand (smooth
splash) part in Fig. 5. About these furrows we shall have something to
say later.
A better idea of the extreme thinness of the enveloping sheath is
obtained when the illumination is from behind as in Series X, in which
the sphere was of highly polished serpentine stone 2·57 cm. (or just
over 1 inch) in diameter, the fall being 14 cm. (or not quite 6 inches).
[Illustration: SERIES IX
The "sheath" splash of a smooth sphere.
1 T = 0
2 0·002 sec.
3 0·013 sec.
4 0·024 sec.
5 0·039 sec.
6]
Examination of either Series IX or Series X shows that with the smooth
sphere as with the rough the amount of water lifted above the surface in
the immediate neighbourhood of the splash is much less than the whole
volume displaced, so that we are again driven to the conclusion that the
surface at even a considerable distance must be bodily lifted without
its flatness being sensibly disturbed. This conclusion was confirmed by
a direct experiment. The not very wide vessel of Fig. A was taken and
filled brimful with milk, and the lower edge of a card millimetre scale
was placed just in contact with the liquid surface at one side. The
reader should notice that the liquid is not quite up to the level of the
spout on the right-hand side of this figure. Then the sphere was dropped
in and the photograph of Fig. B was taken when the sphere was about
two-thirds immersed. The rise at the edge of the scale is about 3
millimetres, and there is an apparently equal rise at the spout, where,
however, the surface appears quite flat.
[Illustration: FIG. A]
[Illustration: FIG. B]
It seems probable, then, that whenever a stone is thrown into a lake the
impulse accompanying its entry travels with the velocity of a
compressional wave (i.e. with the velocity of sound) through the
liquid, and is therefore almost instantly felt and produces a minute
rise of level even in remote parts of the lake long before the arrival
of any ripple or surface disturbance.
[Illustration: SERIES X
Polished serpentine sphere falling 14 cm. into water.
1 0·003 sec.
2 0·006 sec.
3 0·008 sec.
4 0·011 sec.
5 0·013 sec.
6 0·014 sec.]
It may here be observed that whether the sphere be rough or smooth, its
size makes little or no difference in the character of the splash,
within a range of diameter from 12 to 32 millimetres--i.e. from about
1/2 inch to about 1-1/3 inches. No doubt with a very large sphere,
taking a long time to enter, the splash would be controlled more by
gravity than by surface-tension, but so long as the sphere is within the
limits mentioned this is not the case unless the height of fall be made
very small indeed.
CHAPTER VIII
THE TRANSITION FROM THE SMOOTH OR "SHEATH" SPLASH TO THE ROUGH OR
"BASKET" SPLASH
THE INFLUENCE OF VELOCITY.
If we gradually increase the velocity with which a well-polished sphere
enters the liquid we find that there is a gradual transition from the
silent "smooth" or "sheath" splash taking down no air and giving rise to
only an insignificant column, to the noisy, "rough," "basket" splash
taking down much air and throwing up a tall and conspicuous jet. Thus in
the fourth figure of Series XI, in which the height of fall has been
increased from 15 to 60 cm. (i.e. from 6 inches to 2 feet), the sphere
being of polished ivory, we see that the enveloping sheath has in many
places broken away from the surface before the summit has been covered.
It is well known that a sphere moving through a liquid pushes away the
liquid in front of it, which flowing round closes in at the back of the
sphere.
Although the surface round the column of Fig. 6 is still very flat, the
liquid just below it must be streaming inwards,[G] as is indicated by
the radial striæ. To the meeting of these converging streams we must
attribute the large access of liquid that is forced up into the column,
whose subsequent toppling into drops is accompanied by the curious,
characteristic, lop-sided curvature of the later figures.
[Illustration: SERIES XI
Polished ivory sphere, 1·9 centim. in diameter, falling 60 cm. into
water mixed with milk.
1
2 T = 0
3
4 0·002 sec.
5
6 0·004 sec.
7 0·031 sec.
8 0·045 sec.
9 0·062 sec.]
Series XII shows how even with a very highly polished metal sphere
falling into water from the still greater height of 100 cm. the
characteristic sheath of the "smooth" splash is no longer so closely
fitting even at an early stage, but is beginning to resemble the earlier
stages of the basket-shaped crater of the "rough" splash; yet no air was
taken down at this height.
The transition was also watched by means of photographs taken below the
water-line.
It may be well here to guard the reader against a possible
misconception. The curved outline of the liquid in these photographs
does not represent the path followed by the particles. Each particle
must have travelled in a nearly straight line from the moment it left
the surface of the sphere, and must still be moving upwards and
outwards. Gravity has not had time to produce any sensible displacement.
This applies also to the curved outlines in many other early figures.
INFLUENCE OF THE CONDITION OF THE SURFACE.
By very careful rubbing of such a polished, steel sphere, it was found
possible to increase the height of fall to 162·5 cm. (well over 5 feet)
and yet to secure a perfectly "airless," "smooth" splash. But the
equilibrium of the splash, if I may use the phrase, is, at this high
velocity of entry (564 cm. per sec., or about 18 feet per sec.), very
unstable, and was found to depend on minute differences in the condition
of the surface. How minute this difference may be, which yet makes the
whole difference in the character of the splash, may be gathered from
the following extract from the original paper:--
"A polished steel sphere 15·9 cm. in diameter was found (by naked-eye
observation) to give an airless splash when falling into water from a
height of 132·5 cm.; at 137·5 cm., there was much air taken down. This
observation at 137·5 cm. was repeated three times, observer C. doing the
polishing. Then observer W. polished, and the splash was first _nearly_
airless and then _quite_ airless. Then, by persevering in the rubbing,
the height of fall was gradually raised to 162·5 cm., and a perfectly
airless splash was secured, and even at 172·5 cm. the record was 'very
little air indeed.'
"Again, a polished marble sphere 2·57 cm. in diameter falling into water
from a height of 112 cm. was found to take down 'much air' when rubbed
with a certain clean handkerchief A, and 'none at all, or only very
little,' when rubbed with clean handkerchief B. This result was
confirmed four times with B and five with A. These handkerchiefs were
subsequently examined under the microscope, but were found to be
extremely similar, and the cause of the difference remained for the time
beyond conjecture.
"On another occasion, of two similar nickel-plated steel spheres, each
19 millimetres in diameter, and each treated in exactly the same way,
falling 22 cm. into paraffin oil, one would always take down much air
and the other little or none, and again microscopic examination showed
only a very slight difference in the surfaces."
[Illustration: SERIES XII
Smooth sphere of polished serpentine falling 100 centim. into water.
Scale 3/4.
1 T = 0
2 0·001 sec.
3 0·002 sec.]
By wetting the surface of a smooth sphere we can always convert a smooth
or "sheath" splash into a rough or "basket" splash. Thus when the ivory
sphere (which when dry and well-polished gave, with a fall of 60 cm.,
the splash of Series XI, p. 97), was allowed to fall _wet_ into the
liquid, all other circumstances remaining the same, the splash of Series
XIII, p. 103, was obtained, which is entirely different from the first.
The wetting was effected by dipping the sphere into the bowl of milky
water into which it was to fall, and then shaking off as much as
possible of the adherent liquid, but in all cases the splash quickly
became unsymmetrical, probably through the liquid, during the fall,
drifting to one side of the sphere.
INFLUENCE OF THE NATURE OF THE LIQUID.
The nature of the liquid employed has a great influence in determining
whether at a given height the splash shall be "rough" or "smooth."
Thus with paraffin oil the maximum height that could be reached with an
airless splash with highly polished nickel-plated spheres, well rubbed
on a selvyt cloth, was found to be only 24·7 cm. (about 10 inches), but,
with water, a fall of 160 cm. (over 5 feet) could be reached. The
paraffin oil used in these experiments had, at a temperature of 12°·5
centigrade, a specific gravity ·840 and a surface-tension about ·39 of
that of water. Since only a small increase of height was required with
this liquid to make a smooth sphere give the same splash as a rough
one, this liquid was found much more convenient than water in
investigating the transition.
When water is made more viscid by the gradual addition of glycerine,[H]
the surface-tension and the specific gravity are but little altered
though the viscosity is steadily and sensibly increased. An admixture of
two parts of glycerine to fifty-one of water produced no perceptible
change in the splashes observed. When the glycerine was increased to six
volumes in fifty-one of water, though this made the viscosity half as
great again, the change was noticeable but still slight, the chief
difference being, with a smooth sphere, the greater salience of the ribs
or flutings in some of the earlier stages of the glycerine splash, and
the much greater reluctance of the subsequent jets to topple into
droplets. This latter feature is well seen in the first figure on page
105, showing the entry of a smooth sphere of polished serpentine stone
into this glycerine mixture from a height of 50 cm.
[Illustration: SERIES XIII
Splash of a smooth wet sphere.
1 T = 0
2 0·003 sec.
3 0·015 sec.
4 0·037 sec.]
With pure glycerine, which is much more viscous, the splash of the same
polished serpentine sphere falling from 75 cm. (about 2-1/2 feet), is
shown in Series XIV. In the original photographs the radial furrows on
the right-hand side of Fig. 2 are very pronounced, and even in Fig. 1
the fluting of the film is seen to be already well developed on the
left-hand side; but these details have proved rather too delicate for
reproduction in the plate. Two photographs taken of stage 2 had each of
them an isolated jet, owing probably to the fact that when working with
so sticky a liquid it was difficult to avoid contaminating the cloth on
which the sphere was each time repolished after washing in water, with
the result that the spheres behaved as if locally rough. The relatively
great length and height of this jet brings out well the part played by
viscosity, both in delaying segmentation into droplets and also in
hindering the flow of the rest of the liquid sheath which has remained
in contact with the sphere.
With a rough sphere falling into pure glycerine from the same height of
75 cm., except for an occasional jet that may escape as in Fig. 4 of
Series XV, the proceedings are uneventful, as a glance at the series
will show. With the same height of fall into water we should have had an
exquisite crater fringed with a multitude of fine jets, and ultimately
closing to form a bubble. We thus see how little play is given to the
action of the surface-tension in a very viscous liquid.
[Illustration: Polished stone sphere falling 15 centim. into water mixed
with glycerine.]
[Illustration: SERIES XIV
Polished stone sphere falling 75 centim. into pure glycerine. Scale
9/10.
1 2 3]
[Illustration: SERIES XV
Rough sphere falling 75 centim. into pure glycerine. Scale 1/1.
1 T = 0
2 0·001 sec.
3 0·002 sec.
4 0·003 sec.]
THE INFLUENCE OF TEMPERATURE.
It was found that if a polished sphere was heated in boiling water,
quickly rubbed dry, and let fall while still hot, a very marked
difference was produced. With the sphere hot, the height of fall can be
much increased before the splash becomes "rough." Thus with paraffin
oil, the height with a nickel-plated sphere rose from 22·2 cm. to 29·3
cm., and with water from 157 cm. to 234 cm.
THE REMARKABLE INFLUENCE OF A FLAME HELD NEAR THE LIQUID, AND TRAVERSED
BY THE SPHERE IN ITS FALL.
In our search for the explanation of the difference between the rough
and the smooth splash, it occurred to us to let the smooth sphere drop
through a flame held near the liquid, and the result was very
remarkable. With paraffin oil (and the sphere hot) the airless height
now rose from 29·3 cm. to 45·3 cm., and with water and a cold sphere, it
rose from 157 cm. to over 258 cm., which was the greatest height that
the laboratory would permit. Either the luminous flame of a bat's-wing
burner or the flame of a Bunsen burner held nearly horizontal produces
the effect, provided the flame is held near enough to the surface of the
liquid, and it is a very striking experiment to let the polished sphere
fall several times from a height which gives a large volume of bubbles
rising with much noise to the surface, and then to let it fall through
the flame, and to observe the complete change in the phenomenon. On a
sphere already roughened the flame has no observable effect.
THE SUPPOSITION OF ELECTRIFICATION TESTED AND REJECTED.
The behaviour with a flame led at first to the supposition that we had
to deal with an electrical phenomenon, for a flame would certainly
discharge completely any electrified sphere passing through it, and it
appeared reasonable to suppose that the sphere might become electrified
by friction with the air through which it fell.
It required a long series of experiments, into the details of which I
need not now ask my readers to enter, to prove that this tempting
explanation was untenable, and that there was no reason to believe that
electrification had anything to do with the matter.
EXPERIMENTS IN VACUO.
It remained to examine what part was played by the air in the whole
transaction. This could only be settled by removing the air and letting
the spheres, whether rough or smooth, fall through a vacuum into the
liquid, or rather through a space occupied only by the vapour of the
liquid in use.
Instantaneous photographs obtained under these conditions showed that
the presence of the air has no material influence on the early course of
the splash, and that a sphere which gives a "smooth" splash in air will
give a "smooth" splash in vacuo, while if the splash is "rough" in air,
it will also be "rough" in vacuo.
FOOTNOTES:
[G] Some useful information about the internal flow of the liquid was
obtained by the device of letting the sphere descend between two slowly
ascending streams of very minute bubbles liberated by electrolysis at
two electrodes placed in the liquid. These streams, initially straight
and vertical, were displaced and distorted as the sphere passed near
them and afforded a measure of the displacement of the fluid at
different points. For details see _Phil. Trans. Roy. Soc._, Vol. 194, p.
178 (1900).
[H] Glycerine was found to be a rather treacherous liquid, requiring
special precautions for which the reader who desires details is referred
to the original memoir. _Phil. Trans. Roy. Soc._, Series A, 1900. Vol.
194, p. 198.
CHAPTER IX
THE EXPLANATION OF THE CAUSE OF DIFFERENCE BETWEEN THE TWO SPLASHES
I have some hope that, by the enumeration of the many surprising and
puzzling facts mentioned in the last chapter, I may have succeeded in
producing in the mind of my reader some sympathy with the state of
perplexity of Mr. Cole and myself when, after four years of
experimenting, we found ourselves still unable to answer the question,
"Why does the rough sphere make one kind of splash, the smooth sphere
another kind?"
By reflecting, however, on all the facts at our disposal, we were at
last led to what seems to be an entirely satisfactory explanation, and
one moreover which we were able to test by further experiment.
This explanation may be stated as follows:--
When a sphere, either rough or smooth, first strikes the liquid, there
is an impulsive pressure between the two, and the column of liquid lying
vertically below the elementary area of first contact is compressed. For
very rapid displacements the liquid on account of its viscosity behaves
like a solid. In the case of a solid rod we know that the head would be
somewhat flattened out by a similar blow, and a wave of compression
would travel down it; to this flattening or broadening out of the head
of the column corresponds the great outward radial velocity, tangential
to the surface, initiated in the liquid, of which we have abundant
evidence in many of the photographs. (See pp. 75, 87, and 99.)
Into this outward-flowing sheath the sphere descends, and since each
successive zone of surface which enters is more nearly parallel to the
direction of motion of the sphere, the displacement of liquid is most
rapid at the lowest point, from the neighbourhood of which fresh liquid
is supplied to flow along the surface. Whether the rising sheath shall
leave the surface of the sphere, or shall follow it, depends upon the
efficiency of the adhesion to the sphere. If the sphere is smooth and
clean, the molecular forces of cohesion will guide the nearest layers of
the advancing edge of the sheath, and will thus cause the initial flow
to be along the surface of the sphere.
To pull any portion of the advancing liquid out of its rectilinear path
the sphere must have rigidity. If the advancing liquid meets loosely
attached particles, e.g. of dust, these will constitute places of
departure from the surface of the sphere; the dust will be swept away by
the momentum of the liquid which, being no longer in contact with the
sphere, perseveres in its rectilinear motion. If the dust particles are
few and far between, the cohesion of the neighbouring liquid will bring
back the deserting parts, but if the places of departure are many, then
the momentum of the deserters will prevail. Thus at every instant there
is a struggle between the momentum of the advancing edge of the sheath
and the cohesion of the sphere; the greater the height of fall the
greater will be the momentum of the rising liquid, and the less likely
is the cohesion to prevail, and the presence or absence of dust
particles may determine the issue of the struggle.
Roughness of the surface will be equally efficient in causing the liquid
to leave the sphere. For the momentum will readily carry the liquid past
the mouth of any cavities (see Fig. 20), into which it can only enter
with a very sharp curvature of its path. It is to be observed that the
surface-tension of the air-liquid surface of the sheath will act at all
times in favour of the cohesion of the sphere, and even if the film has
left the sphere the surface-tension will tend to make it close in again,
but we should not be right in attributing much importance to this
capillary pressure which, with finite curvatures, is a force of a lower
order of magnitude than the cohesion, and, as the photographs now to be
shown will clearly show, is incompetent to produce the effects observed.
[Illustration: FIG. 20]
Having arrived at this general explanation, we proceeded to test it.
EXPERIMENTS ON THE INFLUENCE OF DUST.
In the first place, to test the influence of dust, the experiment was
made of deliberately dusting the surface of the sphere. For this
purpose a highly polished nickelled sphere was held in a pair of
crucible tongs by an electrified person standing on an insulating stool,
and by him presented to any dusty object that stood or could be brought
within reach. Particles of dust soon settled on the electrified sphere,
which was then carefully placed on the dropping ring with the dusty side
lowest. The liquid used was paraffin oil, and the height of fall was
31·7 cm., at which this sphere when not dusted gave always a quite
airless splash. When dusted an enormous bubble of air was carried down
on each occasion. Although the sphere when laid on the dropping ring
must have completely lost the electrical charge, yet it seemed worth
while to go through the same electrifying process without dusting. The
result showed that no change was produced. In order to see how far the
influence of dust would go, the height of fall was now reduced, and it
was found that with sphere (1) a fall of 17·1 cm. gave a perfectly rough
splash when the surface was visibly dimmed with fine dust, and with a
second similar sphere a fall of 16·7 cm. availed. If the surface was
only slightly dusty, then at these low heights the splash remained
"smooth."
It then occurred to us to try the effect of partial or local dusting,
for we had already found by experimenting with a marked sphere that the
method of dropping did not impart any appreciable rotation to the
sphere, which reached the liquid in the attitude with which it started
from the dropping ring. Accordingly, after dusting the sphere in the
manner already described, the dust was carefully rubbed away from all
but certain parts whose position was recorded. The experiments were very
successful, and the results are shown on page 113. The liquid used was
water, and the sphere was of polished serpentine, 2·57 centim. in
diameter, falling 14 centim.
In Fig. 1 of Series XVI the sphere was dusted on the _right-hand side_,
and a "sound of splash" was recorded. On the left side we see that there
is no disturbance of the "smooth splash"; on the right is a "pocket" of
air such as was obtained by accident in Series IX, Fig. 6 (see p. 91).
The point of departure at which the liquid left the sphere is well
marked, and a tangent from this point passes through the outermost
conspicuous droplets that must have been projected from it.
In Fig. 2 the sphere was dusted _at the top and on the right-hand side,
but not much more than half-way down_, and the configuration corresponds
entirely to the facts. Here again a tangent from the well-marked drops
on the right-hand side leads very nearly to the place of departure from
the surface of the sphere.
In Fig. 3 the sphere was dusted near the bottom only. The appearance on
the left-hand side seems to show that the liquid has, after leaving the
sphere, again been brought within reach. This recovery at an early stage
is explained by reference to photographs of Series VI (p. 81) of the
splash of a rough sphere, which show that even the rough sphere is soon
wetted for some distance up the sides, by the gradual passage of the
sphere into the divergently flowing cone of liquid which surrounds the
lower part. When the liquid again touches a polished part the film will
be again guided up it in the manner already explained.
[Illustration: SERIES XVI
Spheres dusted at one side.
1 2 3]
We observe that in Figs. 1 and 2 (as also in Fig. 6 of page 91) the
continuous film or shell of liquid no longer reaches the outermost
droplets that once have been at its edge. It must evidently have been
pulled in by its own surface-tension, which of course will cease to
exercise any inward pull on a drop that has once separated.
The influence of dust, thus incontestably proved, seems also to afford a
satisfactory explanation of--
(1) The effect of a flame.
(2) The effect of heating.
(3) The variable and uncertain effects of electrification.
For, (1), we may suppose that the flame burns off minute particles of
dust; (2), we know from Aitken's experiments[I] that dust from the
atmosphere will not settle on a surface hotter than the air; (3) an
electrified sphere descending through the air would attract dust to its
surface unless it happened, as well might happen, that the air round
about it, with its contained dust, had become itself similarly charged
through the working of the electrical machine.
In further confirmation of our view that the leading clue to the
explanation of the motion is the struggle between the adhesion of the
rigid sphere and the tangential momentum of the liquid, we may cite the
following points:--
A _liquid_ sphere makes a "rough" splash, and the photographs obtained
show that the lower part of the in-falling drop is swept away by the
tangential flow, while the upper part is still undistorted. Here we have
cohesion but no rigidity.
Also we find that the "rough" splash is obtained by any process which
gives a non-rigid surface to the sphere. Thus the splash made by a
marble freshly roughened by sand-papering, or by grinding between two
files and let fall from the very small height of 7·5 cm., can be
practically controlled by attending to the condition of the surface. If
the surface is quite dry and still covered with the fine powder
resulting from the process of roughening, the splash is "rough," and a
great bubble of air is taken down. But if this coat of powder, which has
neither cohesion nor shearing strength, be removed by rubbing, the
splash (under this low velocity) is "smooth." Again, a marble freshly
sand-papered and covered with the resulting powder, if let fall from 12
or 15 cm., gives a rough splash. The same marble picked out of the
liquid and very quickly dropped in again from the same height, will give
again a rough splash. Here the liquid film is thick and "shearable." But
if the same sphere be allowed to drain or be lightly wiped, the splash
will be smooth. We may conjecture that in this case enough fluid is left
to fill up the interstices, but that the coat is not thick enough to
shear easily. If, however, the sphere be thoroughly dried, the splash
becomes "rough" again. This gives us the explanation of the facts
already recorded in respect of the splash of a wet sphere. This splash
was always irregular; the liquid drifted to one side where it would
shear, while it disappeared from the other or became there too thin to
shear, though sufficient to fill up crevices.
EXPLANATION OF THE RIBS OR FLUTINGS IN THE SPLASH OF A SMOOTH SPHERE.
The fact thus established experimentally, that the surface of a smooth
sphere must be rigid if the film is to envelop it closely, suggests also
a satisfactory explanation of the flutings. For we know from other
researches on the motion of liquids,[J] that a layer of liquid actually
in contact with a solid can have no motion relative to the solid, but
must move with it. Thus in the film or sheath which rises over and
envelops the sphere, the layer of liquid next to the solid must be
moving downwards with it, while the outermost layers at least are moving
upwards; thus there must be a strong viscous shear in the film impeding
its rise. If by any fortuitous oscillation a radial rib arises, this
will be a channel in which the liquid, being farther from the surface,
will be less affected by the viscous drag; it will therefore be a
channel of more rapid flow and diminished pressure, into which,
therefore, the neighbouring liquid will be forced from either side. Thus
a rib once formed is in stable equilibrium, and will correspond to a jet
at the edge of the rim. This explains the persistence of the ribs when
once established, and we may attribute their regular distribution to the
fact that they first originate in the spontaneous segmentation of the
annular rim at the edge of the advancing sheath. This explanation quite
accords with the appearance of such figures as Fig. 6 of page 91 and
Figs. 1 and 2 of page 113, in which, firstly, we see that the flutings
are absent from that part of the sheath which has left the sphere, and,
secondly, we see how much higher in every case the continuous film has
risen in that part which has left the sphere than in the part which has
clung to it, and has been hindered by the viscous drag. Especially is
this the case in Fig. 2, Series XIV (p. 105), where the liquid was pure
glycerine. The effect of the viscous drag is, in fact, most marked in
the most viscous liquid, and it is also in the viscous liquid that the
ribs are most strongly marked.
INFLUENCE OF THE NATURE OF THE LIQUID EXPLAINED.
Finally, in confirmation of our explanation, we have the fact that with
a liquid of small density and surface-tension, such as paraffin oil, a
much smaller velocity of impact with a highly polished sphere suffices
to give a "rough" splash than with water, a liquid of greater density
and surface-tension, the reason being without doubt that the tangential
velocity given by the impact is greater with the lighter liquid, as,
indeed, is proved to be the case by the greater height to which the
surrounding sheath is thrown up. The surface-tension also being smaller,
the less is the abatement of velocity on account of work done in
extending the surface.
FOOTNOTES:
[I] See _Nature_, vol. xxix., January 31, 1884.
[J] See Whetham on "The Alleged Slipping at the Boundary of a Liquid in
Motion." _Phil. Trans. Roy. Soc._, Vol. 181 (1890).
CHAPTER X
CONCLUSION
We have now reached the end of the story, as far at least as I am able
to tell it. But there is certainly more to be found out. No one has yet
examined what happens when a rough sphere enters a liquid with a very
high velocity. That the motion set up must differ from that at a low
velocity is apparent to any one who has thrown stones from a low bridge
into deep water below. The stone that is thrown with a great velocity
makes neither quite the same sound nor the same kind of splash as a
slow-falling stone, and though in the light of our present knowledge we
may conjecture the kind of difference to be expected, yet experience has
taught me that the subject is so full of unexpected turns that it is
better to wait for the photographic record than to speculate without it.
It would be an immense convenience, as was suggested in the first
chapter, if we could use a kinematograph and watch such a splash in
broad daylight, without the troublesome necessity of providing darkness
and an electric spark. But the difficulties of contriving an exposure of
the whole lens short enough to prevent blurring, either from the motion
of the object, or from that of the rapidly-shifting sensitive film, are
very great, and any one who may be able to overcome them satisfactorily,
will find a multitude of applications awaiting his invention.
But even were the photographic record complete, what does it amount to?
All that we have done has been merely to follow the rapid changes of
form that take place in the bounding surface of the liquid. The interior
particles of the liquid itself have remained invisible to us. But it is
precisely the motion of these particles that the student of
hydrodynamics desires to be able to trace. His study is so difficult
that even in the apparently simple case of the gently-undulating surface
of deep water, the reasoning necessary to discover the real path of any
particle can at present only be followed by the highly-trained
mathematician. In other and more complicated cases such as are
exemplified by the sudden disturbances that we have studied, any
definite information that can be obtained, even as to the motion of the
surface, may afford a clue to the solution of important questions; and I
have been encouraged to hope that the observations here recorded may
serve as a useful basis of experimental fact in a confessedly difficult
subject.
To take a single illustration of a possible application in an unexpected
quarter, I would invite the attention of the reader to the two
photographs in the frontispiece, which exhibit the splash of a
projectile on striking the steel armour-plate of a battleship. These are
ordinary photographs taken after the plate had been used as a target.
They represent the side on which the projectile has entered. In one
picture the projectile is still seen embedded in the plate.
No one looking at these photographs can fail to be struck with the close
resemblance to some of the splashes that we have studied. There is the
same _slight_ upheaval of the neighbouring surface, the same crater,
with the same curled lip, leading to the inference that under the
immense and suddenly applied pressure, the steel has behaved like a
liquid.
Such flow of metals under great pressure is familiar enough to
mechanical engineers, but what I desire to suggest is, that from a study
of the motions set up in a liquid in an analogous case, it may be
possible to deduce information about the distribution of internal
stress, which may apply also to a solid, and may thus lead to
improvements in the construction of a plate that is intended to resist
penetration.
CHAPTER XI
(SUPPLEMENTARY)
A NEW PHENOMENON THAT APPEARS WITH AN INCREASE IN THE VELOCITY
OF ENTRY OF A ROUGH SPHERE
A slight delay in the passage of this book through the press has enabled
me to obtain some of the missing information referred to in the opening
paragraph of the last chapter.
If any reader who may have been persuaded to try for himself the simple
experiment mentioned at the beginning of Chapter VII, will extend his
observations by increasing the height of fall of the roughened marble to
4 or 5 feet (say to 140 centim.), he will find that while, as before,
much air is still carried down, there is nevertheless, now, no
rebounding jet projected high into the air, such as is invariably seen
with the lower fall of 2 feet (60 centim.), and he will notice a curious
"seething" appearance at the surface.[K] Thinking that this appearance
which the naked eye detects must be due to an entanglement of the rising
jet with the bubble, which entanglement was likely to produce confused
motions that could not be profitably studied, I had not till now been
sufficiently curious to examine what really happened. But certain recent
observations of the persistence with which the seething motion again and
again recurred when a stone was dropped or thrown into a river, led me
to suspect that something required investigation. I was, however, quite
unprepared to find the remarkable change of procedure that is revealed
by the following series of photographs (Series XVII), in the taking of
which I owe much to the kind and skilful assistance of Dr. Bryan. The
earlier figures show the very rapid rise of the crater and its closing
as a bubble much before the entrapped column of air divides. Before the
division takes place, the liquid now flowing in from all sides closes
over the upper end of the long air-tube, separates it from the air
outside, and _forms a downward jet which shoots down the middle of the
air-tube in pursuit of the sphere_. The first formation of this jet is
not easy to observe, because the view is obscured by much splashing and
turbulent vortical motion resulting apparently from the collision of the
streams that converge from all sides on the axis of the air-tube at its
upper end. Thus in Fig. 5 the jet is not yet well established, or at
least not easily discerned; but in Fig. 6 the turbulence has cleared
away from the upper part, and from this stage onwards the jet is well
seen in all the figures, and it persists long after the segmentation of
the air column has taken place. The reader must not suppose that this
jet is a mere _falling_ of the water under the action of gravity, for
the rapidity with which it advances is far greater than could be
accounted for in this way; indeed, as the "times" show, the effect of
gravity during the establishment of the jet is insignificant.
[Illustration: SERIES XVII
Rough sphere falling 140 cm. into water. Scale 2/3.
1 0·006 sec.
2 0·008 sec.
3 0·015 sec.
4 0·021 sec.
5 0·038 sec.]
The segmentation of the air column appears to be independent of the jet;
but some photographs, such as Fig. 7, show the jet striking the side and
breaking into the surrounding liquid with a great accompaniment of
"air-dust."
[Illustration: SERIES XVII--(_continued_)
6 0·043 sec.
7 0·052 sec.]
N.B.--Each of these figures is made up from two photographs; one of the
upper and one of the lower portion taken from different splashes, but
with the same "timing."
The reader will observe that after division of the air-tube has taken
place, say from Fig. 9 onwards, the water entering the jet at the top
and coming out again at the bottom must circulate as in a vortex ring,
part of the core of which is filled with the air surrounding the jet.
It is also to be observed that after the establishment of the jet, there
is a steady increase in the size of the heap above the surface; but it
is not easy in any given photograph to say how much of this protuberance
is air and how much is water. An examination of Figs. 7, 8, and 9 shows
that the place of origin of the jet is gradually lifted above the level
of the free surface.
That the jet we now see should be directed downwards rather than upwards
may, I think, be explained in a general way as follows:--The great
initial momentum of the sphere causes it to continue in rapid motion
after the bubble has closed, thus the sphere acts as a sort of piston,
which by increasing the length of the air-tube diminishes the pressure
in it and so sucks in the bubble, which is driven down by the greater
atmospheric pressure above. The converging horizontal inflow near the
mouth of the air-tube cannot, of course, produce the downward-directed
jet without an equal and opposite generation of momentum upwards; but
this is now expended, not in producing a similar upward jet, but in
balancing the excess of atmospheric pressure. The reaction, in fact, to
the projection of the jet downwards, is the force which holds up and
slowly raises the roof of the long air-shaft.
[Illustration: SERIES XVII--(_continued_)
8 0·057 sec.
9 0·063 sec.
10 0·073 sec.
11 0·089 sec.]
When, as in the last figure of Series VI, p. 85, we saw the
upward-directed jet, then also there must have been an equal and
opposite generation of downward momentum distributed in some way through
the liquid below the basin, of which, however, there could be no visible
sign. Hence we see that the present downward jet is, in a sense, not a
new phenomenon, but one which, having existed unnoticed before, is now
rendered visible to us by reason of its being produced in air instead of
in water.
By means of a hole bored through the ceiling of the dark room, the fall
was then increased to 281 centim. (just over 9 feet). The very beautiful
earlier stages of the splash at this height are shown in Series XVIII.
Fig. 4 shows very well the internal splashing at the top of the
air-column which accompanies the initiation of the jet. Some later
photographs taken at this height (not yet quite presentable) show the
jet passing right down the narrow neck of air-tube and probably striking
the top of the sphere, the descent of which must thus be liable to a
curious irregularity.
A further increase of the height of fall to 686 centim. (22-1/2 feet)
was found to produce but little change in the phenomena.
[Illustration: SERIES XVIII
Early stages of the splash of a rough sphere (diam. 1·5 centim.) falling
281 centim. (about 9 feet) into water.
1 T = 0
2 0·003 sec.
3 0·005 sec.
4]
FOOTNOTES:
[K] I can recommend any reader who is not afraid of being late for
breakfast to keep a bag of marbles in his bath-room.
PRINTED BY
WILLIAM BRENDON AND SON, LTD
PLYMOUTH
[Transcriber's Note: The following changes have been made to the
original text.
Page 10: "the same in 1, 3 and 4" changed to
"the same in 1, 2 and 4"
Page 66: "·04 of a gram" changed to "0·4 of a gram"
Page 77: Added full stop to image caption 9 "0·042 sec."
End of Project Gutenberg's A Study of Splashes, by Arthur Mason Worthington
*** END OF THIS PROJECT GUTENBERG EBOOK A STUDY OF SPLASHES ***
***** This file should be named 39831-8.txt or 39831-8.zip *****
This and all associated files of various formats will be found in:
http://www.gutenberg.org/3/9/8/3/39831/
Produced by Jana Srna, Alexander Bauer, Erica
Pfister-Altschul, and the Online Distributed Proofreading
Team at http://www.pgdp.net (This file was produced from
images generously made available by The Internet
Archive/American Libraries.)
Updated editions will replace the previous one--the old editions
will be renamed.
Creating the works from public domain print editions means that no
one owns a United States copyright in these works, so the Foundation
(and you!) can copy and distribute it in the United States without
permission and without paying copyright royalties. Special rules,
set forth in the General Terms of Use part of this license, apply to
copying and distributing Project Gutenberg-tm electronic works to
protect the PROJECT GUTENBERG-tm concept and trademark. Project
Gutenberg is a registered trademark, and may not be used if you
charge for the eBooks, unless you receive specific permission. If you
do not charge anything for copies of this eBook, complying with the
rules is very easy. You may use this eBook for nearly any purpose
such as creation of derivative works, reports, performances and
research. They may be modified and printed and given away--you may do
practically ANYTHING with public domain eBooks. Redistribution is
subject to the trademark license, especially commercial
redistribution.
*** START: FULL LICENSE ***
THE FULL PROJECT GUTENBERG LICENSE
PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK
To protect the Project Gutenberg-tm mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase "Project
Gutenberg"), you agree to comply with all the terms of the Full Project
Gutenberg-tm License available with this file or online at
www.gutenberg.org/license.
Section 1. General Terms of Use and Redistributing Project Gutenberg-tm
electronic works
1.A. By reading or using any part of this Project Gutenberg-tm
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or destroy
all copies of Project Gutenberg-tm electronic works in your possession.
If you paid a fee for obtaining a copy of or access to a Project
Gutenberg-tm electronic work and you do not agree to be bound by the
terms of this agreement, you may obtain a refund from the person or
entity to whom you paid the fee as set forth in paragraph 1.E.8.
1.B. "Project Gutenberg" is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg-tm electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg-tm electronic works if you follow the terms of this agreement
and help preserve free future access to Project Gutenberg-tm electronic
works. See paragraph 1.E below.
1.C. The Project Gutenberg Literary Archive Foundation ("the Foundation"
or PGLAF), owns a compilation copyright in the collection of Project
Gutenberg-tm electronic works. Nearly all the individual works in the
collection are in the public domain in the United States. If an
individual work is in the public domain in the United States and you are
located in the United States, we do not claim a right to prevent you from
copying, distributing, performing, displaying or creating derivative
works based on the work as long as all references to Project Gutenberg
are removed. Of course, we hope that you will support the Project
Gutenberg-tm mission of promoting free access to electronic works by
freely sharing Project Gutenberg-tm works in compliance with the terms of
this agreement for keeping the Project Gutenberg-tm name associated with
the work. You can easily comply with the terms of this agreement by
keeping this work in the same format with its attached full Project
Gutenberg-tm License when you share it without charge with others.
1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are in
a constant state of change. If you are outside the United States, check
the laws of your country in addition to the terms of this agreement
before downloading, copying, displaying, performing, distributing or
creating derivative works based on this work or any other Project
Gutenberg-tm work. The Foundation makes no representations concerning
the copyright status of any work in any country outside the United
States.
1.E. Unless you have removed all references to Project Gutenberg:
1.E.1. The following sentence, with active links to, or other immediate
access to, the full Project Gutenberg-tm License must appear prominently
whenever any copy of a Project Gutenberg-tm work (any work on which the
phrase "Project Gutenberg" appears, or with which the phrase "Project
Gutenberg" is associated) is accessed, displayed, performed, viewed,
copied or distributed:
This eBook is for the use of anyone anywhere at no cost and with
almost no restrictions whatsoever. You may copy it, give it away or
re-use it under the terms of the Project Gutenberg License included
with this eBook or online at www.gutenberg.org
1.E.2. If an individual Project Gutenberg-tm electronic work is derived
from the public domain (does not contain a notice indicating that it is
posted with permission of the copyright holder), the work can be copied
and distributed to anyone in the United States without paying any fees
or charges. If you are redistributing or providing access to a work
with the phrase "Project Gutenberg" associated with or appearing on the
work, you must comply either with the requirements of paragraphs 1.E.1
through 1.E.7 or obtain permission for the use of the work and the
Project Gutenberg-tm trademark as set forth in paragraphs 1.E.8 or
1.E.9.
1.E.3. If an individual Project Gutenberg-tm electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any additional
terms imposed by the copyright holder. Additional terms will be linked
to the Project Gutenberg-tm License for all works posted with the
permission of the copyright holder found at the beginning of this work.
1.E.4. Do not unlink or detach or remove the full Project Gutenberg-tm
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg-tm.
1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg-tm License.
1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including any
word processing or hypertext form. However, if you provide access to or
distribute copies of a Project Gutenberg-tm work in a format other than
"Plain Vanilla ASCII" or other format used in the official version
posted on the official Project Gutenberg-tm web site (www.gutenberg.org),
you must, at no additional cost, fee or expense to the user, provide a
copy, a means of exporting a copy, or a means of obtaining a copy upon
request, of the work in its original "Plain Vanilla ASCII" or other
form. Any alternate format must include the full Project Gutenberg-tm
License as specified in paragraph 1.E.1.
1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg-tm works
unless you comply with paragraph 1.E.8 or 1.E.9.
1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg-tm electronic works provided
that
- You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg-tm works calculated using the method
you already use to calculate your applicable taxes. The fee is
owed to the owner of the Project Gutenberg-tm trademark, but he
has agreed to donate royalties under this paragraph to the
Project Gutenberg Literary Archive Foundation. Royalty payments
must be paid within 60 days following each date on which you
prepare (or are legally required to prepare) your periodic tax
returns. Royalty payments should be clearly marked as such and
sent to the Project Gutenberg Literary Archive Foundation at the
address specified in Section 4, "Information about donations to
the Project Gutenberg Literary Archive Foundation."
- You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg-tm
License. You must require such a user to return or
destroy all copies of the works possessed in a physical medium
and discontinue all use of and all access to other copies of
Project Gutenberg-tm works.
- You provide, in accordance with paragraph 1.F.3, a full refund of any
money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days
of receipt of the work.
- You comply with all other terms of this agreement for free
distribution of Project Gutenberg-tm works.
1.E.9. If you wish to charge a fee or distribute a Project Gutenberg-tm
electronic work or group of works on different terms than are set
forth in this agreement, you must obtain permission in writing from
both the Project Gutenberg Literary Archive Foundation and Michael
Hart, the owner of the Project Gutenberg-tm trademark. Contact the
Foundation as set forth in Section 3 below.
1.F.
1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
public domain works in creating the Project Gutenberg-tm
collection. Despite these efforts, Project Gutenberg-tm electronic
works, and the medium on which they may be stored, may contain
"Defects," such as, but not limited to, incomplete, inaccurate or
corrupt data, transcription errors, a copyright or other intellectual
property infringement, a defective or damaged disk or other medium, a
computer virus, or computer codes that damage or cannot be read by
your equipment.
1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the "Right
of Replacement or Refund" described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg-tm trademark, and any other party distributing a Project
Gutenberg-tm electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.
1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium with
your written explanation. The person or entity that provided you with
the defective work may elect to provide a replacement copy in lieu of a
refund. If you received the work electronically, the person or entity
providing it to you may choose to give you a second opportunity to
receive the work electronically in lieu of a refund. If the second copy
is also defective, you may demand a refund in writing without further
opportunities to fix the problem.
1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you 'AS-IS', WITH NO OTHER
WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of damages.
If any disclaimer or limitation set forth in this agreement violates the
law of the state applicable to this agreement, the agreement shall be
interpreted to make the maximum disclaimer or limitation permitted by
the applicable state law. The invalidity or unenforceability of any
provision of this agreement shall not void the remaining provisions.
1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg-tm electronic works in accordance
with this agreement, and any volunteers associated with the production,
promotion and distribution of Project Gutenberg-tm electronic works,
harmless from all liability, costs and expenses, including legal fees,
that arise directly or indirectly from any of the following which you do
or cause to occur: (a) distribution of this or any Project Gutenberg-tm
work, (b) alteration, modification, or additions or deletions to any
Project Gutenberg-tm work, and (c) any Defect you cause.
Section 2. Information about the Mission of Project Gutenberg-tm
Project Gutenberg-tm is synonymous with the free distribution of
electronic works in formats readable by the widest variety of computers
including obsolete, old, middle-aged and new computers. It exists
because of the efforts of hundreds of volunteers and donations from
people in all walks of life.
Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg-tm's
goals and ensuring that the Project Gutenberg-tm collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg-tm and future generations.
To learn more about the Project Gutenberg Literary Archive Foundation
and how your efforts and donations can help, see Sections 3 and 4
and the Foundation information page at www.gutenberg.org
Section 3. Information about the Project Gutenberg Literary Archive
Foundation
The Project Gutenberg Literary Archive Foundation is a non profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation's EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg
Literary Archive Foundation are tax deductible to the full extent
permitted by U.S. federal laws and your state's laws.
The Foundation's principal office is located at 4557 Melan Dr. S.
Fairbanks, AK, 99712., but its volunteers and employees are scattered
throughout numerous locations. Its business office is located at 809
North 1500 West, Salt Lake City, UT 84116, (801) 596-1887. Email
contact links and up to date contact information can be found at the
Foundation's web site and official page at www.gutenberg.org/contact
For additional contact information:
Dr. Gregory B. Newby
Chief Executive and Director
[email protected]
Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation
Project Gutenberg-tm depends upon and cannot survive without wide
spread public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To
SEND DONATIONS or determine the status of compliance for any
particular state visit www.gutenberg.org/donate
While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.
International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg Web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations.
To donate, please visit: www.gutenberg.org/donate
Section 5. General Information About Project Gutenberg-tm electronic
works.
Professor Michael S. Hart was the originator of the Project Gutenberg-tm
concept of a library of electronic works that could be freely shared
with anyone. For forty years, he produced and distributed Project
Gutenberg-tm eBooks with only a loose network of volunteer support.
Project Gutenberg-tm eBooks are often created from several printed
editions, all of which are confirmed as Public Domain in the U.S.
unless a copyright notice is included. Thus, we do not necessarily
keep eBooks in compliance with any particular paper edition.
Most people start at our Web site which has the main PG search facility:
www.gutenberg.org
This Web site includes information about Project Gutenberg-tm,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.
